☰

Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search:
Results: 88065
Make Model Symptom Problem Solution By
CONVERSOR SEMP TCL DC-2008-H
The LED turned on, but tsound was no image I removed the vga heatsink and heated it with a hairdryer for about 5 minutes And it worked normally again, these factory solders have little alloy, so over time they lose their alloy, mad just heat it up again and it's gone. Kohlmann
SEMP TCL DC-2008-H
The LED turned on but tsound was no image It was the VGA with cold soldering, I removed the heatsink and gave it heat With the hairdryer for about 5 minutes and it worked normally again Kohlmann
PHILIPS FWM663
Display turning on and off C13 ( 47uf 50v) e c14 (100uf 16v) Replace them NATO ELETRÔNICA
CCE TL470
Image scrolling.... Alter pal-n to pal-m André
PHILIPS 32PFL5604
Does not turn on, stand-by turns red, but does not change when activating the power on the panel or on the remote control. Capacitor c474 (4.7 x 16 v) on the main board is defective, it is next to the crystal, replace it and run to the hug. Led Tech / Cds_Dias
SOPRADOR TERMICO YAXUN 886
Temperature rose and then fell. Triacs bta 8a 600v Replace the triacs. I put bta 12a for 600v and it was good flavio
SAMSUNG T27B350LB
Restarting Cable that connects the power supply board to the main board Remove it and clean the card input connectors and the power supply board. it worked for me. the TV has returned to normal flavio
SEMP DC-2008H
The LED turned on but tsound was no image I removed the heatsink from the VGA and with it connected to the TV I heated it and the image came back, in other words this type of soldering has little alloy, some do rebaling, I just heated it with a hairdryer for a few minutes and it worked h Kohlmann
SAMSUNG PL51F4000AG
Stretched image Signal board replacement Replace the position of the zr 869 fhd to r860hd or vice versa paulo rps
PHILIPS 32PFL5007
Does not turn on and the LED flashes 3 times Power supply defect, 12v with 9v - works if connected to 220v Replace without measuring q603 - stk0160 type bc, replace without measuring I took it from a scrap yard VICTORINO
SAMSUNG UN32T4300AG
Totally inoperative Shorted diode under the processor heatsink When removing the diode the board started working again Eletrônica JJ
SAMSUNG UN55F7500
Relay keeps disarming Ci in short Replace ci slc1013m cleber lima rs
PHILIPS 40PFL3606D/78
L11M1.1L LA 		Gray image with vertical lines and oscillating 3j26 resistor (240k) open on the timing control board Replace component 3j26 (240k) leitemarcellus
PHILIPS 32PFL7606
LED flashes 3 times and does not turn on I removed the power supply board and tried to assemble it on the bench but without success, after a visual inspection I noticed cold welds on the primary of the t 501 transformer, I redid the welds with reinforcement on the transformer islands and it worked perfectly. MARCOS
SAMSUNG PL51F4000
It doesn't turn on, it only has pson voltage 5v In my case tsound was only 5v voltage pson grounding no voltage appeared tsound was no 5v, 15v, go, vs Replace qq806, 807(std5915) resolved speedtec
PHILCO TV PH21C
Alloy with the weak negative image drizzled as if it were the tube C845 Replace the 1000μF 16v c845 replace without fear Sinailson
ELSYS ETRS35
Absence of signal Tsound was 13v at the tuner output, but when I connected the LNB it dropped to 4.0v Replace r9 470r close to the tuner LOOPTEL
PANASONIC TC-L39B6B
I'm sound. Main board, partially shorted. Short smd ceramic capacitor, look for the av terminals, behind the board tsound is a double transistor, (aadryf), the capacitors next to it replace. (plate without silkscreen printing) RNSPTEC
GRADIENTE 2021
Out of tune Eeprom 24c16 whichever one works, because the processor records it alone Josimar
LG 32LJ600B
LJ7 		The screen LEDs blink and the TV doesn't work 30 volt inverter power supply failure Touch main board SANTOMEL