Sony Repair Tips
Search: sony
Results: 20082
Results: 20082
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CFD757
|
"a" or "b" deck tape door open on stop instead of eject | #252 lever line breaks off under #208 lever, stop. #209slider(s) eject is therefore selected when stop is pressed. | ||
| SONY |
CFS1030
|
No audio - replace q304, p/n 8-729-177-32 | No audio output. | ||
| SONY |
CFD440
|
Tape door opens on stop instead of eject | #151 lever line breaks off under #103 lever, stop. #106slider (s) eject is therefore selected when stop is pressed. | ||
| SONY |
CFD450
|
No audio output - replace ic303, p/n 8-759-822-51 | Unit has no audio on all functions. ic chip is shorted (poweramp). | ||
| SONY |
CFD440
|
Static between tracks - replace ic703, p/n 8-752-337-26 | Static sounds can be heard between tracks using the yeds-1disc. about 4 units out of 35 had this problem or 11%. | ||
| SONY |
CFS1030
|
Door opens on stop instead of eject. | #251 lever line breaks off under #203 lever, stop. #206slider (s), eject therefore selected when stop is pressed. | ||
| SONY |
CFD767
|
"a" deck tap door open on stop instead of eject | #452 lever line breaks off under #408 lever, stop. #409slider (s), eject is therefore selected when stop is pressed. | ||
| SONY |
CFD470
|
Tape door open on stop instead of eject | #354 lever line breaks off under #308 lever, stop. #309slider(s) eject is therefore selected when stop is pressed. | ||
| SONY |
CDX5460
|
Audio cuts out (replace ic503, p/n 8-759-160-98) | Ic503 heats up and loses 8v output, which causes the audio to cut out. | ||
| SONY |
XEC1000
|
Hiss in audio (replace ic103, p/n 8-759-106-02) | A hissing sound is heard from all outputs. | ||
| SONY |
XM2020
|
No power (resolder l901 and repair damaged traces) | Unit has no audio when disassembled, noticed that centerlead of l901 has pulled back through board. this sometimes will cause theother lead to lift the traces from the weight of l901. | ||
| SONY |
XM3020
|
C310 physically damaged and becomes dislodged from main mcb | C310 falls off the board and the amp still works fine. wehave had several units with this problem. | ||
| SONY |
XM2020
|
No audio from 1 channel, replace ic101 or ic201 as required | Unit has no audio from one channel heat sink may or may notbecome extremely hot. ic101 or ic201 has signal at input but not atoutput. | ||
| SONY |
STRAV23
|
Service manual error - correct value for f902 is 3.15a | Service manual lists f902 as being a 5 amp fuse when it isactually a 3.15 amp fuse. | ||
| SONY |
CDPC325
|
No power; erratic display when unit is off (replace ic202) | Display would momentarily light when power switch is turnedon and disc table would continue to spin. when turned off the displaywould sometimes light erratically and the table would continue to spin.upon diagnosis found the reset of ic202 pin 5 was not | ||
| SONY |
CDPH3750
|
No display (repair open traces near t201) | Unit powers up, and will open and close cd table, buthas no display. traces on the transformer board are lifted at t201. | ||
| SONY |
CDP491
|
Clv motor runs when unit is off (q206 installed backwards) | Spindle motor would spin when power switch is turned off.upon diagnosis of the switching circuitry of ic202 found q206 was inbackwards. | ||
| SONY |
CDPC27
|
Door does not stay open (repair open traces near s702) | Cd door opens for a few seconds then closes. traces onopen/up sw board connected to s702 are open. | ||
| SONY |
CDX5060
|
Disc jams during loading (re-seat st lever, ref. 136) | When cd is inserted into unit, it goes about halfway in andthen stops. the unit then begins to make clicking/grinding noises beforeejecting cd. | ||
| SONY |
SPPA20
|
Part number for battery lid base cushion | No part number for battery lid cushion base in servicemanual. |