Repair Tips
Search:
Results: 87970
Results: 87970
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
PH55A17
|
Don't call, don't light up | Micro cold loose | RESOLDAR MICRO | JL ELETRONICA SR |
| TCL |
32R6500
|
That stby | AD 501 w/escape after a radius on the network. | replace Diode FR207 | FBS ELETRÔNICA |
| H-BUSTER |
HBTV-42D06FD
|
Don't tune channels | N100 cold welds | Restol n100 | Mau3000 |
| MONDIAL |
MS-05
|
Does not turn on no sign | It doesn't start at all puts it in the plus, it doesn't start nothing gives no sign | Mondial eletronic | |
| CCE |
LV40G
|
Short circuit power supply Drive LED. | Q501 is FDD120AN15A0 and works the FET ME15N10-G on site. | If it works slightly darker with 70 volts on the LEDs, check/ replace I.C 500 (MP3394) at the power supply, because in my case PWM did not act when replace \\\ "Standard picture for dynamic for staff \\\" and I suspected I.C and really was. After exreplace I.C 500 MP3394 the voltage went to 81.5 volts in the LED exits. | MIGUELTV |
| PHILCO |
PH39N91DSGW
VERSÃO B |
Main plate | replace the plate, everything is the same as | Use PH32B51DSGW Plate A Version | Eletrônica Silva Homs |
| FISCHER |
MICROONDAS 6946-10876
|
Sometimes you doesn't start, don't light up display | Q1 Comp itself | replace of q! (S8050). Can be replaced by BC337 or other equivalent | LABOTRON |
| LG |
60PA6500
|
then turned on and off | resolving the 2 plaque transformers, the small and the largest | reginaldo moronte,eletronica junior caldas novas | |
| SANSUNG |
UN50CU7700
|
Pink and Green picture | After replace the main plate | Remove the IC 503 UT memory that is under the old plate sink and put on the new plate in my case resolved. | Badri eletrônica |
| SAMSUNG |
UN50CU7700
|
Pink and Green picture | After replace the signal plate, the picture came pink and green remove the IC 503 UT which is under the black sink of the old defective plate and puts on the new plate this will solve the problem for me | Badri eletrônica | |
| LG |
HT503SH
|
Turn on and then turn off | DVD circuit, probably driver of the engines | I turned off the flatcable and uses the radio, auxiliary and pendrive. | LOOPTEL |
| LG |
CM995.AB.ABRALLK
|
very low audio at low l output | Missing -b +12V at IC703 | Open contact between R77C and lower contact of the PCB | leitemarcelus |
| LG |
32LJ600B
|
N lights the LEDs | D601 with escape, near the LED connector | Marcelo | |
| SAMSUNG |
UN32FH4205
|
No picture (normal backlight) | AVDD | replace the capacitor that is short CD12, CD13 CD14 or CD15 | Baguatech |
| TCL |
L43S4900FS
|
Flashing the standby LED quickly, nonstop. | Short Mosfet Channel N, Q300 (PC015BD) at the power supply. | replace and go to the hug | World TV - Sorocaba |
| SAMSUNG |
PL51F4900
|
After replace the main plate still did not turn on, without VS voltage, VA low (11V), arming the power supply externally the tensions rise normally. | I used the main plate of PL43F4900 on PL51F4900. As I had already said sound, you need to put the original IC 2001 EPROM memory of 51 \\\ " | Don't do the same as beating my head. Already replace the resistors and memory first of all, when it can make main boards of this TV. | World TV - Sorocaba |
| PHILIPS |
47PFL8606D
|
Does not turn on, flashes standby error 3, tsound are 03 blinked. | Missing 12 volt power supply originating from the main power supply | Cold weld at the Trefo Secondary Terminal that provides 12 volts. | MIGUELTV |
| SEMP |
TV2134 (B) SL
SK11 |
Does not turn on, LED access hits the relay and erases | OS 2 47UF capacitor by 160v | replace of them | AssisTec - Manari/PE |
| SEMP |
TV 2134 (B) SL
SK11 |
When the volume increases the picture begins to tremble | The cause of the defect was the 102K C613 near the primary power supply STRW | To resolve the replace was made by another | AssisTec - Manari/PE |
| PHILCO |
PH55A17DSGWA
VERSÃO C |
doesn't start, just get Standby lit. | Short circuit in the 3V3 line of the main plate, measuring short on the L3D1 coil near the processor. | Defect was the CI U3 oscillator of the 3V3 power supply that was short. I used a similar CI taken from scrap and worked perfectly. | rafaelmoraes99 |