Philco Repair Tips

Search: philco
Results: 4806

Make	Model	Symptom	Problem	Solution	By
PHILCO	PH55A17	Don't call, don't light up	Micro cold loose	RESOLDAR MICRO	JL ELETRONICA SR
PHILCO	PH39N91DSGW VERSÃO B	Main plate	replace the plate, everything is the same as	Use PH32B51DSGW Plate A Version	Eletrônica Silva Homs
PHILCO	PH55A17DSGWA VERSÃO C	doesn't start, just get Standby lit.	Short circuit in the 3V3 line of the main plate, measuring short on the L3D1 coil near the processor.	Defect was the CI U3 oscillator of the 3V3 power supply that was short. I used a similar CI taken from scrap and worked perfectly.	rafaelmoraes99
PHILCO	PCX5501N	PCX5501N all and turn off Off	EEPROM CORRUPPE		NEUPSX4
PHILCO	PH32B28DSGW	Restart	Update	Download the file to Philco, put it on the TV USB, press the pawer key and hold, put it in the plug and wait for it recognizes the update.	Cabeça
PHILCO	PH55M LED SMAT 3D	The TV called and learned the Philco logo then turned off the screen == This TV and the one that has two 83 LEDs regies each.	It was 129v in the exit of the LEDs to the screen.	I removed from the plate inverting the following 3.6Ω resistors in parallel r34 and r65 + r35 and r67 + r38 and r71 and put in the lamp of each resistors of 4.7Ω the voltage went to 122V and went back to work ok	Max Matipó
PHILCO	PH32N62D	TV without Standbay, has no secondary voltage, zener brand*(EA2) which is a short LT431 next to photoacoplator and CI PWM Burned	these components were replaced and was solved		Rodricell
PHILCO	PH32N62D	tv ph32n62d sem backlight	TV PH32N62D without backlight, only 30V arrives, glue under the r35 resistor of the power supply with bad contact		Rodricell
PHILCO	PH21M SS	turn on then turned off	capacitor c803 fault	Just replace the 220UF400V capacitor	Mvp Assistec
PHILCO	PTV40E21DSWNC LED	When replacing LEDs and reducing chain, TV always turns on the first one by giving 53V, turning off in the control and turning again, rises to 63V (ideal).	In the 1k R2B9 resistor scheme, but comes with 10k, replace with 100k	replace resistance r2b9 or remove, device went back to work perfectly	Beto , eletrônica box 4
PHILCO	PB500BT	Sound works and shuts down	Works and off
PHILCO	TV PTV49F68DSGWN	Backlight lit and without picture	In my case it was C216 with escape on the V.Con plate	Just take the capacitor and run to hug	jorge assistencia tecnica cotia sp
PHILCO	PH51U20 DSGW Plasma	TV Liga appears the logo and turns off	replace both 450x 100 C412 and C413 capacitors
PHILCO	PH24M LED A 40-00MS09-MAC2XG	Don't tune channels	Regulador u804 5v as1117 smd	replace the regulator and run to hug in some cases the update solves tb	Rafael Sena
PHILCO ATUALIZAçãO	PHILCO ATUALIZAçãO philco atualização	Philco Update	Philco Update		NEUPSX4
PHILCO	PH50A17DSGWA	Don't turn on or flashing	power supply Primary Defect C.I UW1	replace for C.I P6005 of AOC TVs, but needs to feed pin 3 with 10m resistor from the alternating power supply similar to pin 5 feed	JhonatanSG
PHILCO	PTV32D10N5SKH	connect with normal picture. and gradually falls to led teesan. Until it erases.	replace without testing the capacitor PEC501. 47/100V
PHILCO	PH55E20	Fully stopped, no led stand-by	power supply defect, R7 1K close to the two large capacitors in the middle of the plate		Sylvox
PHILCO	PH21M SS	LED flashing and doesn't start	IC802 TL431	To replace	Eletrônica do Gilvan
PHILCO	PH39N91DSGW	Sometimes it lights standby and calls and sometimes does not light up or call	CW926 with escape	CW926	Bhtechcenter