Philco Repair Tips

Search: philco
Results: 4775

Make	Model	Symptom	Problem	Solution	By
PHILCO	PB500BT	Not switching auxiliary input on plug p2	When opening the jack I saw that the switch was disassembled, I reassembled it and it returned to normal		Paulo Teixeira
PHILCO	PH24M LED A2	No sound in any function, dead audio, no low signal in the Audio stage	Fet smd of position q3 (a03401) on the main board with its "power supply" output with only 7 volts, the correct one is 12 volts.	It was just a matter of changing it and the problem was resolved.	MIGUELTV
PHILCO	PHT550	Totally inoperative	Fuse f1 open and resistor r54 toast (open)	I replaced the fuse and connected it with a series bulb. the fountain began to crackle. I turned off the device and after checking the power supply capacitors, I found only the r54 was toast. In this region, the manμFacturer added glue to secure the power supply's electrolytics. Even though the glue is dry, tsound was probably a current leak. I replaced the resistor and everything went back to normal. As a precaution, I also replaced the following electrolytics that tend to replace over time: e1, e3, e5, e9, e10 and e11.	Técnico Rodrigues
PHILCO	PTV40E21	Does not turn on, when plugged in it blinks slightly 1x standby	U2p1 changed	Replace	ELETRONICA TENSAO R JACUIPE BA
PHILCO	PTV24C10	Does not turn on, standby blinks continuously	Voltages varying in the secondary, defect is in ci uw1 behind the photo coupler		Eletrônica Mirage
PHILCO	PVT40E21DSWN	No audio	Regulator 3v3 u2p2	Replace 3v3 regulator	Tecvideo
PHILCO	PH29E63D	Without with / losing audio	Capacitor	Capacitor next to q22 just above the ci sound output 10μF/16v	Rafael Nunes
PHILCO	PH29B	Turns off after a few minutes 150v normal 125v power supply	R829 of 180k, altered giving 220k	Replace	Hndrsn
PHILCO	PH20U21D	Does not turn on, nor does the standby LED light up.	C820 shorted (smd)		Junior - Tecnoprom
PHILCO	PH55E21DSGW	Does not turn on and without standbay, without 12 and 24 volts at the power supply	Cause r73 1k resistor open, just change it and the TV works again	The r73 in 1b that was open was replaced and the TV started working again.	eletronica cachoeira
PHILCO	PH42M61DSG	Keyboard does not respond	Check regulator n105 near the tuner, check keyboard resistors	Replace 3.3v regulator	Didimo
PHILCO	PH42M61DSG	Tv inoperative without all voltages	Check if tsound is 5v on ci n802	Replace ci 9889	Didimo
PHILCO	PTV40E21	When plugging in the stand-by LED flashes quickly and does not turn on	Regulator 3v3 u2p2 with low voltage 25v	In my case, I replaced the regulator but the defect persisted, I measured the tracks up to pin 1 of the memory, I had to remove the memory to do a reset, I resoldered it again and ran to the hug	INFYNITY Eletronica
PHILCO	PTV32G50SN	Screen lights up but tsound is no image	Capacitor shorted on t-con	Test the 3 capacitors in parallel on the diode side on the right side of the t-con board. If they are shorted, remove one at a time and test until you find which one is shorted.	ELETRONICA KLEIN
PHILCO	PCX6500	Does not load	Power supply	Replace position sb3100 diode d6	Brackmann
PHILCO	PH32U20DSGVA	When it turns on, Philco immediately locks up and turns off and goes back to standby.	Replace faulty nand memory or reprogram nand data	dados nand	neupsx4
PHILCO	PH39F33DSG	Does not light up stand by	1.2v step down power supply u203		Divino Moura
PHILCO	PTV40G65RCH LED	TV doesn't turn on, it just stays on standby	Short circuit on the main board. 5v shorted supply, check smd capacitors ce07, ce08, ce64 of 22ufx6.3v. are close to ci ue01		rafaelmoraes99
PHILCO	PTV22G50D	When plugged in, it takes a while to go to stand by. After this time, the TV turns on.	Change opto coupler. Note, you don't need to measure... and then the defect is remedied		Daniel vieira
PHILCO	PH40U21	LEDs blinking non-stop	Change capacitor in the inverter cap 120uf x 200v stage and go for the hug.		ALBERI F S