Toshiba Repair Tips
Search: toshiba
Results: 5609
Results: 5609
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SEMP TOSHIBA CRT (TV DE TUBO) |
TV2977(A)SL SL-91
|
Reduced frame in the middle of the tube with a glass and time in Lod green, time-colored time and with retrace and without characters. Note: Sometimes when it turned on the frame I would fill the screen again (normal frame) but only the channel character 2 appeared but did not obey the commands. We swear it is a defective primary power supply. | The cause of the malfunction was incredibly damaged Eprom. replaced the EEPROM memory \\\ "resolved headache \\\" ie problem solved. | Airton Eletrônica | |
| TOSHIBA |
52XV550DA
|
Does not care, nor beat relay, tip on which control works on this TV | The less power supply plate has several bad contacts | SOLUTION RESSOLDAR, IN MY CASE I replaced all covers 10/50, 22/50, 4.7/50, ie I reviewed primary. Remote control that works is the MXTCT6390, too top. | MIGUELTV |
| TOSHIBA |
40L2500
|
Alloy, the logo appears, shuts down. | Check CI N804 3.3V regulator. In Sty is 3.0 volt. When it calls it falls to 2.9V. | replace tsound n804. | arock |
| SEMP TOSHIBA/PHILCO |
32AL800/LE3264/PH32E53
FONTE PE371CO/40-E371C6-PWG1XG |
Green LED connect and sometimes locked in green or VM | Had 12v but did not have the 5v on l 102 | Q100 D13N3 8 Pins | ELETRONICA BRAMBILA |
| TOSHIBA |
TODA LINHA U17
U17 |
Light the LED quickly erases and drops the tensions | C-864 47m x50 Primary power supply | ELTON CASTRO | |
| SOM TOSHIBA |
MS-8012MU
|
No sound | Earphone plug | replace or jamper with welding | Mario Moreci |
| TOSHIBA |
32L2600
MT56E1 |
No picture, or inverted picture when replace the screen. | Place Project ID 184 | Eduardo Costa. B. F Electronics. BH, Minas Gerais | |
| TOSHIBA |
MS7980
|
connect and after already turns off | glue on top of the SMD ceramic capacitor next to the flash memory | Remove the glue, replace the capacitor and leave for the hug | Valdecir Schena |
| SEMP TOSHIBA |
40AL800A
|
Green LED, has 3.3V without 24V, locked in the inoperative green LED | replace TL431 (U402), replace photo coupling (PC2) | Gaeletronica | |
| TOSHIBA |
LC404
|
No picture, with sound. | SMD 125V/7A (F102) Open and CI 4614B (Q310) | replace CI and replace fuse, Note. (Redo the weld of all jumpers OOO resistor of the plate), including those that marked heating under the plate, as they are the causes of CI burn with cold welding increasing the tension over the CI. | Wortec |
| TOSHIBA |
48L2400
|
Only Led Stand by Red Acid | Replacement of CI N801 FR9889 | reginaldo moronte,eletronica junior caldas novas | |
| TOSHIBA |
32L2400
|
Defective or broken display | replace display. | The C320an02S4LV0.1 Display works in place if the picture is inverted use the 924263 serial software. | Capiroto |
| TOSHIBA |
TV 1454(P)
|
power supply varying flashing LED | 20K tripote at RP 501 power supply | replacement | Beto |
| STI SEMP TOSHIBA |
DL3254
|
No picture, only the lit LEDs/backlight | SMD CD17 Capacitor shortly on the display/von plate | Remove or replace CD17 on VCON | Wsmartcell |
| SEMP TOSHIBA |
LC3246 B WDA
|
After much insisting it on and turns off immediately. | All tensions, capacitors and connectors were checked. Guilty was the button turns on and off with the worn membrane. | MarceloPiranga | |
| SEMP TOSHIBA |
40L2400
|
Flashing fast light and power supply-bomb | N 802 altered | replace n 802 av 9889 | Ric |
| SEMP TOSHIBA |
DL3245I(A)
|
Don't turn on, stand by red | CI N801 (FR9889) defective. | Enter 12V no more had at 1.15V at the exit. | Alessandro Barcelos |
| TOSHIBA |
40L2400
|
Turns on, then turns off | Voltage regulator | ||
| TOSHIBA |
48L2400
|
missing +5v | Before replace the FLS206MR, replace the NB955 photocoupler (defective) | HAHNRAHN | |
| TOSHIBA |
48L2400
|
Nor +5v | Before replace the FLS206MR, replace the NB955 photocoupler (defective) | HAHNRAHN |