Cce Repair Tips
Search: cce
Results: 4831
Results: 4831
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
D3201 CW3201
cce |
Works for days and you doesn't start anymore | Resolde d7 | resoldar diode d7 | mendes am |
| CCE |
STYLE D46
|
Sound Dark Screen | Um capacitor 20pf x 6kv na pci lateral | Remove that av TV goes back to work because I didn't find the lamps | Warley |
| CCE |
C390
|
Sometimes it does not turn on or off after a short time. | 3V3 U2 regulator (is close to EEPRON). It was measuring 2.78v. | Just replace straight. | R-Tec |
| CCE |
C420
|
TV Normal turns on and works a time and then crashes with liter and a loud sprinkle noise. | Defect in the U5 TRASITOR REGULATOR OF 1.8 V | replace | RV ELETRONICA GYN |
| CCE |
C420
|
TV Normal turns on and works a time and then crashes with liter and a loud sprinkle noise. | Defect in the memory .. | replace or rewrite memory | RV ELETRONICA GYN |
| CCE |
LN24GW
|
Nothing works | C.I. U12 - 9435 (actually a fet) Short on R208 | Eletrônica do Alemão | |
| CCE |
L244
|
Call everything normal, after 10 turns off from nothing. Calls again and the stay tied on is decreasing. | replace both capacitors at 12V power supply (1000UF X25V) | replace of the cited capacitors. | arock |
| CCE |
LN24G
|
Does not turn on short at the entrance | CI 9435 Position U12 | UTI das tvs e microondas | |
| CCE |
LV40G
|
Short circuit power supply Drive LED. | Q501 is FDD120AN15A0 and works the FET ME15N10-G on site. | If it works slightly darker with 70 volts on the LEDs, check/ replace I.C 500 (MP3394) at the power supply, because in my case PWM did not act when replace \\\ "Standard picture for dynamic for staff \\\" and I suspected I.C and really was. After exreplace I.C 500 MP3394 the voltage went to 81.5 volts in the LED exits. | MIGUELTV |
| CCE |
STILE D3201
|
Don't turn on, with the orange LED flashing | PFC CI in the short | replace the U1 with the number 1607b which is under the power supply plate, near the large capacitor | Wsmartcell |
| CCE |
STILE D3201
|
It turns on, lights Stanby, when tightening Power replaces green and nothing happens, then blinks error 7 in the power supply LED. | High tension T1 at the power supply, after suffering to the damn, as it takes the stroke to test another I already visualized the charred winding at one point of the traf. | replace T1 (MIP320g-a-T1/TLT-2796) of the MIP320G-HV0 power supply. Explaining line of reasoning: the 5 volts and power on font appeared and also the 12 volt and 24 power supply appeared, but only the 5 volts and power on, so I suspected the stuff after putting one point of the multimeter at the exit of the trafa and I could see a small high voltage spark and that's wsound I suspected the tread, but the TV was not lumped, so I discarded, so In the end everything worked out. | MIGUELTV |
| CCE |
LT32G
LT32G |
Do not light the LEDs | Diode with altered internal capacity (it seems like joke) measuring this good, but in the equipment of the low capacitance. | Diodo D3 (SB5150) | Johnatan |
| CCE |
STILE D3201
|
Backlight access, without picture | Tsound was no 12V and 24V. Causes cold welds on the power supply plate | Eletrônica Cecé, Brumadinho MG | |
| CCE |
HPS2997
|
Without sound with picture | C661 470/16 with escape | replace | Hndrsn |
| CCE |
TV - 2118 USP / AV
|
Reduced picture on the right side of the screen | R 307 of 330R and R 308 , R 309 of 1R | replace | Mauro Mascarenha Tel. (88) 981422821 Parazinho - ce |
| CCE |
C320
|
When plugged into the socket, the stand-by LED lights up red. When the power key is pressed, the stand-by LED turns green. No voltage appears beyond the 5 volts of stand-by | Q12 pnp smd transistor does not receive positive voltage at the base, in this case because it is pnp it remains in conduction between emitter and collector, keeping pin 8 (soft start) of the U5 SG3525 grounded, which prevents its PWM oscillation. Defect in the microcontroller on the protection plate. SOLUTION: REMOVE Q12 FROM THE SUPPLY BOARD. | Reginaldo Pereira | |
| CCE |
LED 24TV
|
Doesn't turn on | Check cold welding at the power supply. | Resolder font | Rafael, Tecnico. |
| CCE |
STILE D4201
|
Erasing BL quickly when turning on | Inverter Mosfets Driver | I replaced all sot23 SMDs between the SG2535 and the driver trafinho | Davi.sls |
| CCE |
STILE D32
MLT320 |
doesn't start | U3 | replace, the schematic doesn't show the IC code, but I use the same size LD7531AMGL and the pinout matches perfectly. | Play back |
| CCE |
STILE D3201
|
turns on, then turns off, green LED flashing | 5 leaky tec toc key, replace them all | guinga sdia goias |