Cce Repair Tips

Search: cce
Results: 4834

Make	Model	Symptom	Problem	Solution	By
CCE	LH42G	No standby, power supply defect, adaptation of another power supply plate	For those who have not been able to raise the power supply, have the option of using Philco power supply. I used a MLT666 of PH32m2 pH32m3	Reorganize the whip according to tensions (5V, 5VSB, 12V and PS-On), and inverter (24V and GND). After that, the pins will be left on/off and adj. Just join them respectively, then instead of the drive passing through the power supply, goes straight from the main sign to reverse. It is 100%	World TV - Sorocaba
CCE	LT32G	When turning on the power, fast red blinks and then flashing blue and it takes well until standby, after tightening Power it is flashing blue again takes well and does not light the backlight, illuminate with a flashlight is written CCE and is indefinitely, ie, processing stick, memories. sound uses memory 25L1606e.	I wrote to warn friends that this is not the memory U103, memory 25L1606e, because I physically rewrite the memory, I updated via pen drive and nothing. I removed the memory I recorded and put it on another sign that worked perfectly.	So I concluded that the defect is not a memory U103, unfortunately I could not solve, it must be the Flash Nand memory, this I did not replace, disappoint friends but will not time Iguel I lost thinking that the memory U103.	MIGUELTV
CCE	LT32G Gt1326ex d292	LED is flashing blue and red	Don't turn on		ANAILTON
CCE	D3201 CW3201 cce	Works for days and you doesn't start anymore	Ressold d7	ressold diode d7	mendes am
CCE	STYLE D46	Sound OK, Dark Screen	Um capacitor 20pf x 6kv na pci lateral	Remove that av TV goes back to work because I didn't find the lamps	Warley
CCE	C390	Sometimes it does not turn on or off after a short time.	3V3 U2 regulator (is close to EEPRON). It was measuring 2.78v.	Just replace straight.	R-Tec
CCE	C420	TV Normal turns on and works a time and then crashes with liter and a loud sprinkle noise.	Defect in the U5 TRASITOR REGULATOR OF 1.8 V	replace	RV ELETRONICA GYN
CCE	C420	TV Normal turns on and works a time and then crashes with liter and a loud sprinkle noise.	Defect in the memory ..	replace or rewrite memory	RV ELETRONICA GYN
CCE	LN24GW	Nothing works	C.I. U12 - 9435 (actually a fet) Short on R208		Eletrônica do Alemão
CCE	L244	Call everything normal, after 10 turns off from nothing. Calls again and the stay tied on is decreasing.	replace both capacitors at 12V power supply (1000UF X25V)	replace of the cited capacitors.	arock
CCE	LN24G	Does not turn on short at the entrance	CI 9435 Position U12		UTI das tvs e microondas
CCE	LV40G	Short circuit power supply Drive LED.	Q501 is FDD120AN15A0 and works the FET ME15N10-G on site.	If it works slightly darker with 70 volts on the LEDs, check/ replace I.C 500 (MP3394) at the power supply, because in my case PWM did not act when replace \\\ "Standard picture for dynamic for staff \\\" and I suspected I.C and really was. After exreplace I.C 500 MP3394 the voltage went to 81.5 volts in the LED exits.	MIGUELTV
CCE	STILE D3201	Don't turn on, with the orange LED flashing	PFC CI in the short	replace the U1 with the number 1607b which is under the power supply plate, near the large capacitor	Wsmartcell
CCE	STILE D3201	It turns on, lights Stanby, when tightening Power replaces green and nothing happens, then blinks error 7 in the power supply LED.	High tension T1 at the power supply, after suffering to the damn, as it takes the stroke to test another I already visualized the charred winding at one point of the traf.	replace T1 (MIP320g-a-T1/TLT-2796) of the MIP320G-HV0 power supply. Explaining line of reasoning: the 5 volts and power on font appeared and also the 12 volt and 24 power supply appeared, but only the 5 volts and power on, so I suspected the stuff after putting one point of the multimeter at the exit of the trafa and I could see a small high voltage spark and that's wsound I suspected the tread, but the TV was not lumped, so I discarded, so In the end everything worked out.	MIGUELTV
CCE	LT32G LT32G	Do not light the LEDs	Diode with altered internal capacity (it seems like joke) measuring this good, but in the equipment of the low capacitance.	Diodo D3 (SB5150)	Johnatan
CCE	STILE D3201	Backlight access, without picture	Tsound was no 12V and 24V. Causes cold welds on the power supply plate		Eletrônica Cecé, Brumadinho MG
CCE	HPS2997	Without sound with picture	C661 470/16 with escape	replace	Hndrsn
CCE	TV - 2118 USP / AV	Reduced picture on the right side of the screen	R 307 of 330R and R 308 , R 309 of 1R	replace	Mauro Mascarenha Tel. (88) 981422821 Parazinho - ce
CCE	C320	When plugged into the socket, the stand-by LED lights up red. When the power key is pressed, the stand-by LED turns green. No voltage appears beyond the 5 volts of stand-by	Q12 pnp smd transistor does not receive positive voltage at the base, in this case because it is pnp it remains in conduction between emitter and collector, keeping pin 8 (soft start) of the U5 SG3525 grounded, which prevents its PWM oscillation. Defect in the microcontroller on the protection plate. SOLUTION: REMOVE Q12 FROM THE SUPPLY BOARD.		Reginaldo Pereira
CCE	LED 24TV	Doesn't turn on	Check cold welding at the power supply.	Resolder font	Rafael, Tecnico.