Cce Repair Tips
Search: cce
Results: 4831
Results: 4831
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
LT32G
|
Don't tune in | Change varicap from another cce board that is a similar model ln32g, etc. | reginaldo moronte,eletronica junior caldas novas | |
| CCE |
TV 2118USP/AV
|
Low volume | R681 (smd) between the terminals of capacitor c666, remove it from the board | Remove the r681, smd, 22k from the board that is between the c666 terminals | MARCONES DE ARARIPINA-PE |
| CCE |
TV 2918 USP/AV
|
Vertical closed at the bottom, and with lines on the screen. | C417, c424 and c428 amended. | MARCONES DE ARARIPINA-PE | |
| CCE |
TV 2118USP/AV
|
Alloy with closed vertical, at the bottom, and retraction lines | C417 c424 and c428 swap all. | MARCONES DE ARARIPINA-PE | |
| CCE |
TV 2918 USP/AV
|
Reduced frame, with lines. | Capacitors c417, c428 and c424, replace them all, and resolder them on the vertical output. | Replace c417 c428 and c424 | MARCONES DE ARARIPINA-PE |
| CCE |
HPS-2118AVP
|
Low volume | Q101( bc337/25 ) grounded! close to the varicap. | In my case, I thought it would be better to replace it with a Kia7805. I just had to remove the resistor r412, and connect the middle pin, directly to ground. | Marcones de Araripina-PE |
| CCE |
LN244W
|
Doesn't start. Standby LED does not light up | Ec4 capacitor main board | Replace it and run for the hug | XANDARE |
| CCE |
TVS-2910FS
|
Does not turn on, standby LED is off, no secondary voltage | Capacitor c816 (470mfx400v) completely exhausted | Replacing capacitor c816 (primary power supply) | Bruno C. Rodrigues |
| CCE |
C420
|
Turns on normally, crashes with stripes on the screen and loud noise from the speakers. | Regulator u5 changed - normal voltage 1.8 volts | Pardal-X | |
| CCE |
HPS-14XX HPS-20XX
34BI |
Power supply with 70v and it doesn't go up | R817 amended | Replace r817 | Fofão estância |
| CCE |
C4601I
|
Blinking but not turning on | Ld33 regulator | I replaced the LD33 regulator and the capacitor near it, the TV started working again! | Marcelo |
| CCE |
LN39G
GT-1326EX-E39 |
Does not turn on, the stand-by LED is weak, varying in brightness, sometimes it turns on. | Low voltage and varying in the ci u2 regulator 3.3v due to the resistor r29 being cold soldered. The resistor was resoldered and the voltage of 3.3v was stabilized and turned on again. | Cezz@r Augusto | |
| CCE |
HPS 2118 AV
|
Horizontal dark stripe on the side | Ceramic capacitor c434 between flay back and the anode of the abl diode | Raimundo | |
| CCE |
C4601I
|
Turns on the logo appears and turns off the backlight | Inverter output capacitors ck15a ck15b + capacitor +b doubtful to change too | reginaldo moronte,eletronica junior caldas novas | |
| CCE |
STILE D42
GT309PX-V302 |
Noise from the power supply turns on then turns off the green LED lamps on the power supply blinking | Change capacitor ec3 power supply 180n for 450v solved | Nao | Jonatas Silva Ribeiro |
| CCE |
LT29G
|
Access service mode | Power supply2580 no controle | Fernando S | |
| CCE |
HPS 1407
|
LED blinks but won't turn on | Transformer t401 open, just change the run to another | sergio marques | |
| CCE |
LT29G
|
Gray screen with audio | Pci vcom with short .12v ok up1 no voltage comes out | Cd20 | samuel leite |
| CCE |
LT29G
|
LEDs light up more when the screen is washed | Change capacitors cd9, cg21 on vcon | Replace the same | renildo |
| CCE |
HPS 2073
|
Heating horizontal output transistor | Short fly back | Colocar bsc-25-0274e | TELE RADIO |