Cce Repair Tips
Search: cce
Results: 4824
Results: 4824
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
CCE |
29USP
RM6-23 |
It doesn't turn on, it takes a little longer to light up, the stand doesn't just turn on normally when the LED lights up | C808 10uf by 50v exhausted | Put a 10μF for 100v | Marqueis eltec eletrônico |
CCE |
HPS-2097
|
Without sound, nothing happens, not even softly | R-631 c645 c632 e correr pro dim dim | eletronica publison natal rgn | |
CCE |
HPS2971
|
Vertical with only half open | 51 volt power supply changed | Replace zd304 smd , no c.i. saida vertical | eletronica fernandes |
CCE |
D3201
|
No audio | Even with the replacement of the EC4 and the Q12 mute transistor, the problem was not resolved. The defect was actually in the audio output u11 ad52582a | TV CENTER GUAIBA | |
CCE |
D42
|
Does not turn on! only red LED | Regulator u5 of 1.8 volts | Replace of the same | Rodrigo cofferi |
CCE |
HPS2185
|
No sound, or missing sound. | Lack of 5v in the power supply of the ci xaveador av tv and the same 5v as the varicap. | Bc337 q101 | ELTON CASTRO |
CCE |
LH42G
|
Does not tune in to any digital channels | Tsound was a power outage and after that no digital channels came on. Go into the menu and restore factory defaults and nothing helped. Remove the varicap to measure the tension and it was normal. I put the varicap back together and tuned again and, oddly enough, the channels tuned in. I don't know what happened, if this tip worked, the TV started working normally again. It must have failed when the power went out. | I removed the varicap, I did the tuning without the varicap and then I put the varicap back on and the tuning went back on | ADRIANO MIRANDA |
CCE |
STILE D3201
|
The red LED doesn't turn on, press power and it doesn't turn on. 5volts present at the power supply, 12volts absent, pfc does not activate | Change circuit transistors invert q20 to q23 r90a r87. replace q6 in primariod3 r97a and r11 both 10homs, ci pfc defective ci l6562 compatible | ||
CCE |
TV 2118USP/AV
|
Just spots on the screen with no image | Solda fria no vertical tsound. | Resolder or vertical ci | MARCONES DE ARARIPINA-PE |
CCE |
TV 2118USP/AV
|
Rainbow effect. | Solda fria no vertical tsound. | Resolder or vertical ci | MARCONES DE ARARIPINA-PE |
CCE |
HPS2991
|
It has the normal +b, the LED is on but it doesn't turn on, it doesn't oscillate. | A silly cause, broken line between the fly back output and the transistor collector. check | Check continuity between fly back pin and transistor collector. | Luiz Carlos |
CCE |
HPS14 BPS
|
Takes time to call. | Open resistor, 10k r823 open or altered. position between pin 1 of IC 804 and pin 4 of IC 805 (regulators). | After changing the TV ok. | George Pontes |
CCE |
D24LED
1.10.73305.02REV1A |
Compatibility between cards | The l2401 board is the same, including the same memory data | Eletronica Muniz | |
CCE |
L2401
1.10.73305.02REV1A |
Compatibility between cards | The d24led board is the same, including the same memory data | Eletronica Muniz | |
CCE |
D37 D40 D42 D46 D4201
|
Orange LED stuck on stand by. | I have already repaired several boards by replacing the 1.8v u5 regulator, but I replaced the regulator on this one and the same symptom continued. | Replace without measuring the capacitor ec4 470x16 (1.3v) that is connected to coil l1 | |
CCE |
HPS-2971N
|
Turns on with excessive high and turns off in 2 seconds. | Cause abl circuit to change q404_c421_r423_r427, it worked perfectly after the repair. | Anderson Eletrônica A&M | |
CCE |
HPS 1404
|
+b on flayback with 46v. instead of 103 | Remove flayback or isolate +b, if you return to 103v power supply. Just change the flay tat1409 | Replace o flay tat1409 | JGC Eletronica |
CCE |
HPS 1404
|
Dark tele with closed at the bottom | Capacitor 1nf c904 na placa rgb | Replace it without measuring and celebrate!!! | JGC Eletronica |
CCE |
HPS 1471
|
Intermittent on and off | Leaky or short diodes, d 101 and d 711. Note they were whitish. | After changing the TV ok. | George Pontes |
CCE |
2118USP
|
Vertical does not open, tsound is a blue stripe slightly above the middle of the screen | Falta +12v pino 2 ci out vert | Defect elco position c546 open power supply diode filter d542 replace and that's it and thank lord jesus for the tip | irmao |