Cce Repair Tips

Search: cce
Results: 4824

Make	Model	Symptom	Problem	Solution	By
CCE	HPS 2071	When starting, the LED starts to flash quickly, providing protection.	Q403 and q404 if you remove the jump jc 11 next to the flyback the TV will work again but the problem needs to be resolved	Replace	Eletrônica Mauro Mascarenha - Parazinho Ceara - Tel : (88)981422821
CCE	LT29G	Blue LED doesn't turn on	Change q10 code a1	You can put another one with code A4 without any problem	eletronica rodrigues
CCE	HPS-21AVP	Tsound is no audio or sound, tsound was a lack of 5 v on pin 16 of the ci 603 and tsound was a short from the aforementioned pin to ground.	C 107 of 470/16 v shorted and r 103 of 33 r open, replaced everything ok		Eurípedes
CCE	LT32G	If, when you replace the card for another, the image turns upside down	Just replace the flash memory u103		Reinaldo
CCE	520USX	Opens and closes the drawer without stopping	Change the contact that is in the drawer between the reader and the tray and then		eletronica publisom de natal rgn
CCE	520USX	Everything stopped	Replace ci viper 22 a		eletronica publisom de natal rgn
CCE	TLCD-32X TLCD32X	Nothing turns on...it has 300 volts from the mains supply, without other voltages.	Photo coupler pc 601, when heated welder, tv worked. but when cold it didn't turn on.	Just replace the pc601, the sound was also hissing, replace the ce115.	Eletrônica Moises N.H
CCE	TVS 2910FS	TV completely turned off without stand by	Diode d811 shorted on the +b line.	Replace diode d811 and check d807.	Gilmario
CCE	D32 LED	Audio only.	Broken wire at the foot of the LED bar. 47x100v capacitor on the inverter swollen (I don't remember the position).	I lowered the circuit current. I added the 2r2 resistor to the 1r resistor already existing in the inverter, position r166 (1r). the measurements went from 59.4v and 601ma to 57.4v and 464ma. to avoid return.	Eletrônica R-Tec
CCE	HPS2071 HPS1471 HPS2073	Inoperative does not turn on primary power supply does not osila	Ic801 = tea1533at short and c806 be careful after a lot of work, just change this cap. the starting power supply		EletronicaArni-SC
TV CCE	TV-2118USP/AV SL23-1	LED blinks intermittently and does not turn on	C831de1000uf-16v	Replace c831de1000μF-16v	Leandro
CCE	STILE D46	Lamps off	Ck15b with leak = 100pf x 5kv in the CN 12 connector of the lamps	Replace without testing good luck...!	Jhone eletronica
CCE	STILE D42	Stops working with the pinkish drizzle screen, noise in the audio.3.3v low.	C156 100mf with leak on the u3 side		E cobra
CCE	STILE D42	To work with the pinkish drizzle screen, 3.3v low.	C156 with leak on the u3 side		E cobra
CCE	HPS 2007	This TV arrived sound at electronics with the stand bay ledy on when pressing the power key, the ledy just blinks intermittently and the TV doesn't go to the armpit!	T401	The T401 had one of the wires broken, I soldered the wire and turned the TV on, forced it to the oxilor and the bu4508dx horizontal output broke. I replaced the t401 and put the new bu4508dx and that's it, the TV worked normally, the t401 was replaced!	Sinailson furtado
CCE	HPS2991SFC	Turns on oscillates, lights up tube filament and then goes out and relay doesn't work, change the two bc337 transistors and the Vila TV works normally, I hope someone helps you, my colleague.	The two bc337 in the horizontal circuit	One was open, replace the transistors	Sammael Kuznetsov
CCE	TVS 2910FS	Defect	Rainbows	Burning fr423	Maciel porto
CCE	LK42D	Turn off the LEDs and only the sound remains (all LEDs are good)	Replace r15 you have to for 100k (solved) replace directly		ELETRONICA AUDIO E VIDEO BIRIGUI-SP
CCE	HPS2971N	Filament lights up and goes out a few times and the TV doesn't turn on.	Fr431 open and d410 shorted.	Replacing the components resolved the failure.	WAINER TELECOM
CCE	D4201	It doesn't turn on, it doesn't light anything.	Defective primary.	Identified several burned components. ((q1 - mdf13n50), (f1 - 6.3 a), resistors r13a, r14a, r14, r15, r16, all (0r68 - 2w) and 2 smd resistors on the solder side, r18 and r19 of 4r7, after changing everything, the power supply turned on, but the lamps kept blinking and the pfc voltage was low (160v), when checking it was identified r 21 of 470r open., after the replace everything worked..... a lot of work to find, phew... .