Cce Repair Tips

Search: cce
Results: 4824

Make	Model	Symptom	Problem	Solution	By
CCE	HPS-1497	Line of retraces and lower half of the screen without image.	C425 470/10v capacitance exhausted.	Replace for a new one.	Carlos M. Prado
CCE	HPS-1403	+ b with 82v, Flybeck does not generate 12 and -12v, press power and the LED goes out as if it were going to turn on and it does not turn on.	Changing the changed r817, from 2k5 it was measuring 3k5, in the schematic it is 2k8.		Manoel Damião
CCE	LW144	Doesn't start	Stand by led off, this TV hears an electrical discharge, burned some components u5-rtd2684d shorted, u12-mp1484en shorted, q11/q22/q23 - code x1lv =( x1 .. ) - ao3401a mosfet, the gate is not arming bad mosfet replaces all,u13 - code iacwc=( iacw..) c/d/j..=mp1472 shorted, r194/r195 - 4k7 smd with leak, r190/r191 - 22k smd changed r193 - 10k open and r192 - 0r smd open.	All these components were replaced, the TV was ok, the defect was resolved	Autorizada CCE
CCE	L144	Doesn't start	Stand by led off, this TV hears an electrical discharge, some components burned out u5-rtd2684d in short, u12-mp1484en in short, q11/q22/q23 - code x1lv =( x1 .. ) - ao3401a mosfet, the gate is not arming bad mosfet replaces all,u13 - code iacwc=( iacw..) c/d/j..=mp1472 shorted, r194/r195 - 4k7 smd with leak, r190/r191 - 22k smd changed r193 - 10k open and r192 - 0r smd open.	All these components were replaced, the TV was ok, the defect was resolved	Autorizada CCE
CCE	CW3201	It arrived dead, without standby.	The TV arrived with the power supply already working and the fuse blown. When analyzing I saw that tsound was a shorted MOSFET (position Q1). It had already been replaced but was probably not original.	Replace the fet q1 and fuse and run to the hug.	PL Eletrônica
CCE	HPS2071 34BI	Does not turn on or stby (led)	C808 22uf50v with high esr		eletrofenix
CCE	HPS 2185 FSH HPS21	Image looking like a rainbow	The cause of the defect	And the solution	raimundo
CCE	HPS-21AVP	Short fly-back	Fly-back	Replace the fly-back bsc25-0206h this fly-back is the same tat2012	Sinailson furtado
CCE	TV-2118USP/AV	Carbonized capacitor	C417, c430	Replace c417 from 331k c430 222k	Sinailson furtado
CCE	HPS-2198B	Turns on and off and the LED just blinks +b normal	Crazy d813 was giving resistance to both sides	Just replace and go for a hug "good luck"
CCE	LT29G	When it turns on, it turns on the blue LED and nothing	In u16 9435	Replace of the same	MULTINFORMÁTICA & ELETRONICA
CCE	HPS-1497P HPS-1458	He had a black stripe on his left side and was shaking like a ghost	331por2kv capacitor in position c-417 if this is not your problem, look at all the components on the fly-blak pin 1 track	Just replace and go for a hug "good luck"
CCE	HPS-1497P HPS-1458	He had a black stripe on his left side and was shaking like a ghost	331por2kv capacitor in position c-417	Just replace and go for a hug "good luck"
CCE	HPS 1471	I plug it into the socket, the LED lights up, I press it, it turns on the normal gun power supply with 103v but it doesn't turn on anything, it just stays with the power supply stabilized	Resistor in position fro402 was open	Just replace and go for the hug
CCE	LK42D	Doesn't start	Replace capacitors 1000x35 c44 c37		wesley
CCE	STILE D46	Roasting high capacitor close to the inverter pin CN12 (ck15b)	Defective lamps.	Remove the ck15b capacitor from the board as this will reduce the voltage on the lamps and it will work again. However, I recommend changing the bulbs if you can. In my case, as I hadn't left it like that, I made the customer aware of the problem. TV works for 2 days sound with me connected directly and it didn't work any better.	Romulo
CCE	HPS-1405B	Reduced image of the top and bottom	Resistor in position r308 of 3.3r was altered	Just replace and go for the hug
CCE	D3201	Power supply pulsing 5v voltage	Non-primary diode d3		electros
CCE	TV21US	Does not turn on, +b normal when the power is activated, the LED flashes and comes on again.	Dry capacitor c634 100uf 25v close to transistors q803 and 802.	After changing the TV ok.	George Pontes
CCE	LW244	Does not turn on LED power,.all normal voltages	Solder with soldering station for 2 minutes on IC SDRAM NT5TU64M and Micro Pro.	It works again!	Alextecnico