Philips Repair Tips

Search: philips
Results: 14238

Make	Model	Symptom	Problem	Solution	By
PHILIPS	32PFL3507 42PFL3507	No standby, main killing the 5V	U501 C.I HDMI shortly, and sometimes some capacitor on the track can also be short, replace and run to hug		Barbieri
PHILIPS	50PUG7406/78	Call and come with smooth screen. No T-Con 12V power.	Android System Dravado in \\\ "hardrest \\\" or factory reste.	Since tsound was no 12V arriving at T-Con, tsound was no way to know this soft-locked situation. The solution was FZ in jump in Q401 and on the screen presented to choose Factory Rest. After setting everything, I removed the jump and the TV was working normal.	EVANDO VIANA
PHILIPS	50PUG7406/78	Liga with normal back light and washed screen	No 12 volt voltage in the T-Con fuse	I injected a 9 volt power supply into the T-Con and came Testo's picture. It was just reconfiguring and the television returned to normal with perfect sound and picture. I removed the power supply concluding the series.	TECMIL/MILTON
PHILIPS	20PT3336/78	Not zero secondary	After checking the secondary step including the circuit that makes up the feedback of the coupling photo I found nothing replaced and tsound I died a 123J x 100V polyester capacitor between pin 1 and 4 of the photo coupler and tsound TV went to work normally		Anderson Eletrônica A&M
PHILIPS	14GX	Flyback AT2079-B4 Substitute	Substitute AT2079-B5		Marcones de Araripina-PE
PHILIPS	SW 986 SM	Protection acting intermittently, generating flaws by arming, or not setting up the refe of the speaker	R513/517 resistor terminals with weld oxidized terminals, generating bad contact.	Remove resistors, sand the terminals and resonoliate again	Assolini BR
PHILIPS	43PFG6917/78	Washed screen, without picture, but with lit back light. No power voltage on t_con plate	Perform reset procedure	With the device off the outlet, hold the commander of commands forward toward you. Then connect the device to the outlet, holding the cursor until the device turns on. Then just restart the settings	LABOTRON
PHILIPS	43PFG6917	TV without picture missing the 12 volts on the t.Con plate	Feed the T.Con with the 12 volts and turn on the TV will appear a service menu on the screen asking to do the recept and give a ok the TV will turn off to control and do all the procedures		RJ eletrônica
PHILIPS	42PFL5007	Only Standby lit, don't turn or call	replace Q603 and Q581 (STK 0160) of the power supply for 7N50, and replace the Diode D107 for a 4007, success!		Matrix10y
PHILIPS	50PUG7907/78	Call with washed screen without picture, sometimes does not turn on	It has all the tense, except 12V display, in this case and corrupt software (Android).	At Jampear CI Q401 which releases the 12V to the display, the screen turns on recovery mode, releasing repower supply of resetting Android. At the end withdrawing the jamper.	Beto , eletrônica box 4
PHILIPS	AZ1030	The same fate, tu is moluk.	R (309) 100k Open, Tuner Power.		Wandercy
PHILIPS	HTS3345/78	It does not turn on, it does not light anything and when it turns on the drawer makes the EJECT and forcing the EJECT engine even after the drawer opens total.	power supply 1.8V on the missing main plate. replace without measuring the Didos below:	D201-D202-D203-D204, all are in4007.	MIGUELTV
PHILIPS	58PUG6654/78	Low power supply	Tsound is no current in T with	.......
PHILIPS	47PFL8606D	Does not turn on, flashes standby error 3, tsound are 03 blinked.	Missing 12 volt power supply originating from the main power supply	Cold weld at the Trefo Secondary Terminal that provides 12 volts.	MIGUELTV
PHILIPS	32PHG5102	After replace the logic plate the picture came blurred	Mode of service ID panel from 214 pass to 224	All ok	Medeiros Eletrõnica Barbacena MG
PHILIPS	48PFG5000	Main replace with negative picture	Reference ID of the wrong rear label in the case was 174 even placing the codes all correct continued picture	Used in my case in the mode of service panel ID 189 ... after a lot of headache solved, sir pole your angels sound ...
PHILIPS	XXPFG5000	Main replace with negative picture	Reference ID of the wrong rear label in the case was 174 even placing the codes all correct continued negative picture	Used in my case in the mode of service panel ID 189 ... after a lot of headache solved, sir pole your angels sound ...
PHILIPS	65PUG7406	screen without video, lit LEDs	No VGL voltage (-7.8VDC), turning off flat on the CNX_L2 connector the TV works.	After testing I found a flad defective, exreplace it resolved	jjsantosneto
PHILIPS	42PFL3604/78	Only red led, not part,	C474 replace near the crystal on the main plate	C474 na PCI principal	Rodrigo cofferi
PHILIPS	42PFG6519/78	Back Light deleted	C9105 near Trafo 9101 with poor contact	Replace it	TECMIL/MILTON