Search: philips
Results: 14231
Make Model Symptom Problem Solution By
PHILIPS AJ3150
Clock advancing, radio sound very low and negative voltage on the capacitors on the radio plate It was probably just the capacitor that is connected to the crystal, but when in doubt and due to the age of the device, I replaced all the electrolytic capacitors on both plates (13 in total) and it was perfect. Pedro Igor
PHILIPS 47PFG7109
TPM14 3L LA
Without image, audio ok. Burned out leds Replace the led bars Eletrônica Moises N.H
PHILIPS 43PHG5813
No image with LED on The t-con board does not receive 12v Fb714 missing, broken or open - from underside of board near panel flat Alessandro B. Barcelos
PHILIPS 43PHG5813
Does not turn on or inoperative Na main pci see 5v_stb no l701 and less than 5v_sw no c786 is entered Replace Q706 (aon4421) Alessandro B. Barcelos
PHILIPS 32PHG5813
Does not turn on or inoperative Na main pci see 5v_stb no l701 and less than 5v_sw no c786 is entered Replace Q706 (aon4421) Alessandro B. Barcelos
PHILIPS 32PHG5813
If you are going to replace the main board for another size TV of the same phg5813 Change the u405 memory and the adaptation will work. Alessandro B. Barcelos
PHILIPS 32PHG5813/78
No image with LED on The t-con board does not receive 12v Fb714 missing, broken or open - from underside of board near panel flat Alessandro B. Barcelos
PHILIPS AZ1134
Cd doesn't play radio fails POS Function Key (SW1) or (SW7-A) Function switch replacement or repair ahunaky
PHILIPS FWM998/78
POW600
Sound turns on demo mode partially but does not start +12v low voltage, it was measuring below 9v. In the region of the inductors l1 and l2 of the power supply, the solders were oxidized and tsound was that disgusting glue that after a while gives conductivity. Redo the welds in the region and remove all this factory glue. Don't forget to sand the legs of the inductors and capacitors. Tiago C. Neves
PHILIPS 46PFL7606
Does not turn on, LED flashes 3x Check q403 and q402 LED power supply circuit, one of them has a short circuit. Mirage Eletrônica
PHILIPS FW-C380
FW-C380
Digital erased 4r7 open Digital erased 4r7 open-3211 on board "3211" resistor 4r7 on the power supply board NEUPSX4
PHILIPS 55PFG5100
0000
Retrace or bands on the screen Short display Technical arrangements or workaround lol... on cn 3 I isolated 3 ways 40 to 43, it was clean and crystal clear qsl macanudo lol.... Jhone Eletronica
PHILIPS 32PFL3404
It turns on the sound, the video is loud, and the screen is bright, but then it turns off. Support for two LCD lamps loose. I resolved the two and reinforced the others. Ademir tc
PHILIPS 32PFL5604 32PFL3404
Does not turn on, the stand-by LED lights up and flashes quickly, but the relay does not hit, it does not accept commands via remote or keyboard Power supply defect, 2r2 smd resistor position rb3, on the power supply primary, underside of the board, resistor changed to 15k, is close to the chopper transformer of the 3v3 power supply of the i.c3 fsq510 Replace rb3 MIGUELTV
PHILIPS 42PFL7007
LED on does not turn on Q603 at power supply Tv técnica Prudentópolis
PHILIPS 42PFL7007G
It doesn't turn on anything, not even the LED, it has 3.3v Power supply q581 Tv técnica Prudentópolis
PHILIPS 40PFG5509/78
Sem video, audio e backlight ok Following a tip from colleague jorge tecnica paraná (capacitor cd7) tsound are two other capacitors in parallel to the cd7. In my case, the short was on cd8 DIEGO BOEIRA
PHILIPS 39PFL4707G/78
Working however with backlight off No voltage on the dim pin at the power supply, check ic8107 pin 5 and 6 for a short, also check ics 8101, 8102, 8103, 8104, 8105, 8106 for a short between pin 1 and 5 Replaced ic8107 and ic8102,8106,8104 that were shorted, normalized the dim voltage and backlight working normally INFOMARQUES
PHILIPS 42PFL5508G
Standby light on and won't turn on Defective pfc power supply oscillator, ic9801 Stiltec
PHILIPS 43PFG6917/78
Turns on and locks on logo Disconnect the cable from the socket, with one hand move the cursor forward towards you (keyboard), with the cursor pressed forward connect the cable to the socket, an initializing message will appear, after that make the initial settings, channel tuning, etc. ,it will work perfectly reginaldo moronte,eletronica junior caldas novas