Philips Repair Tips
Search: philips
Results: 14241
Results: 14241
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
PHILIPS |
65PUG7406
|
screen without video, lit LEDs | No VGL voltage (-7.8VDC), turning off flat on the CNX_L2 connector the TV works. | After testing I found a flad defective, exreplace it resolved | jjsantosneto |
PHILIPS |
42PFL3604/78
|
Only red led, not part, | C474 replace near the crystal on the main plate | C474 na PCI principal | Rodrigo cofferi |
PHILIPS |
42PFG6519/78
|
Back Light deleted | C9105 near Trafo 9101 with poor contact | Replace it | TECMIL/MILTON |
PHILIPS |
FWM653
|
Flashing panel and not turning on | Check the 2 belts of the CD Reader | replace belts that he has returned to work | C13 eletronica |
PHILIPS |
47PFG7109
|
Normal alloy, the logo appears, comes channels shut down. It is in this intermittent loop. Sometimes it wages in HDMI or channel, does not respond to the remote control. Turning off the outlet resumes the loop. After a few time on, it returns to normal and does not connect to the internet. | Turn off the \\\ "wi-fi \\\" plate. Everything returns to normal. | Wi-Fi plate replace. | arock |
PHILIPS |
42PFL3508G/78
|
Don't turn on, stand by lit, 5V line marking ~ 3.2V sometimes turned on when I loose a Flat from TCC. | power supply Plate Line 5.2V replaced resistors 9337- 8K2, R9338 - 9K1 Problem Causer IC9304 - AS431AZTR. On the main plate on the 3V3 line the SMD C2104 capacitor | replace the IC9304 for TL431, if it does not yet 5V, evaluate the resistors. Check SMD capacitors of the main board all voltage lines must be consistent with the electric scheme. In my case was the C2104 - 22u. | André Luiz |
PHILIPS |
FW-C155
|
Don't turn on, blink panel and go off | replace without testing transistors 7247 3213 3247 7244 7322, preferably uses BC338 instead of BC337 | HAHNRAHN | |
PHILIPS |
PHILIPS 32PFL3605D/78
Philips 32PFL3605D/78 |
Black screen with background light and sound | SMD resistor of T-Com integrated on the plate at the bottom link <a href = \ "https: //electronica-pt.com/s/21 \" rel = \ "nofollow \" target = \ "_ blank \">>> External link ... </a> Open from the main | Required resistor I made a video that shows the link well External Link. .. | X elétro |
PHILIPS |
42PFL3403
|
Killed, without standby | Replaced U101 damaged, C120 and D107 and on PCB IR Capacitor shortly next to the sensor | ||
PHILIPS |
40PFL9605D/78
|
Does not turn on, LED flashes error 3 times | power supply Plate replace | I went by elimination and tested main PCI, LEDs, TCC and finally the defect was a power supply, I didn't have time to discover the defective component, as I spent a full power supply plate replace budget and approved. | MIGUELTV |
PHILIPS |
40PUG6300/78
|
TV does not call only with power supply 12v ci u8101 does not generate pwm | C8102 with problem | replace C8102 | alixandre louzada |
PHILIPS |
46PFL4908G
|
Tremendous picture | Check the T-Com Auo plate, | Remove R870, R872. R870, turn on with a thin wire to D802/3, turn on R870 to VGH voltage. | Arock |
PHILIPS |
NTX-600
|
Works but no audio | two varistores on power supply one open, 80v low voltage | Replace VR1 =20D241 | CARLOS |
PHILIPS |
FWM570/19
|
Turns on everything works but no sound comes out | Defective headphone recognition key | try to open the key to clean or replace it | zordtech eletronica |
PHILIPS |
NTRX300/78
|
Works but with display off | Shorted capacitor on display board | Replace capacitor ec302 position on board | Aquiles |
PHILIPS |
47PFL3007D/78
|
5V normal, sem 24V e 12V | C703 shorted | SMD electrolytic 220uF/16V C703 on the main PCB below the power supply connector | Ederlin |
PHILIPS |
47PFL3007D/78
|
5V normal, sem 24V e 12V | C703 shorted | SMD electrolytic 220uF/16V C703 on the main PCB below the power supply connector | Ederlin |
PHILIPS |
50PUG7406
|
Dead, no stand by. Arming the power supply, the voltages are all OK | Main board with 2 capacitors shorting out next to a 4r7 coil close to the CN701 connector | Remove and check if the short has disappeared, then replace them. SMD Capacitors C4328 and C4322 | World TV - Sorocaba |
PHILIPS |
32PFL3404/78
|
When turned on, Standby locked | Broken trail at + do c474 | Remove the capacitor and jump from C340 to D1 up to the 3rd dot of the transistor u36 on the side that is not tsound next to C474 itself and solder a new C to make the job look good. | Wilson |
PHILIPS |
42PFL3403 42PFL5403 42PFL6403
|
Nothing turned on or stand by | visually: U101 (FSQ510) cracked with 1 melted pin / C236 ( CAP 2200mf 25v ) Swollen / R101A Torn (120 ohn resistor next to the main fuse) - all were replaced and the problem persisted, I analyzed pin 5 of the FSQ and measured , I found the ZD103 zenner diode broken (SMD under the board), I replaced it and the LED then came back on but it didn't activate the relay, I replaced the relay and everything started working again | replacedo: C236 / U101 / R101A / ZD103 smd / Relé RE1 12v- 250v10a | Guedes Electronic |