Philips Repair Tips

Search: philips
Results: 14241

Make	Model	Symptom	Problem	Solution	By
PHILIPS	43PFG5813	No picture with screen \\\"washed\\\", LEDs on	With the right side viewed from behind, eliminate 8 trails on the left side of the flat		ToniTec
PHILIPS	29PT9467C Sk5 1l ca	picture closed on the side, reduced frame	Defect, replacement of cap c438, 272pf and cap L432 next to the flyback		Dj pituka
LG PHILIPS AOC	43S5195 43S5295 43LJ5500 43PFG5813	Screen flickering lines on the screen	replace the display	I didn't find a cheap display, but I gave the budget based on one on the free market and it was approved, I'll leave the link for anyone who wants to buy it: External Link...	KICO
PHILIPS	MCM595	DOESN'T START	C2217 DRY	replace it	BARBADINHA
PHILIPS	MCM595	stuck in standby	doesn't start	replacing capacitor C2217	BARBADINHA
PHILIPS	42PFG6519 715g6338-p01-000-002s	It doesn't turn on and sometimes the LEDs don't light up	c9311, C9312, C9317, C9318, C9321 all 470x25v burst or with high esr if the LEDs do not light up it would be c9105 polyester mkp 0.022x1000v with cold on its pins	replace all capacitors and resolder the board and look at the speaker	orlando lott
PHILIPS	50 PUG7625	No picture washed screen	Flat cable right side from tcon to vcon	Flat cable right side solar sixth to tenth line	Artur
PHILIPS	25PT848A/55R L01.1L AA	No video input on AV 2 and side AV. I was also having audio problems. Right side very low and being connected to only one input, switching to the other inputs, the television continued to emit sound from the connected input.	To solve the audio problem, replace HEF4052BT (7801). To solve the video problem, replace HEF4053BT (7802). Both are underneath the main board.		Sígmar de Oliveira
PHILIPS	42PFL4908G/78	Does not turn on dead open fuse	Capacitor in power supply c9803	Replace capacitor c9803 and open fuse,	UTI das tvs e microondas
PHILIPS	42PFL3007D/78 42PFL3007D/78	DEAD STAND-BY 0V WHEN CONNECTING CABLE TO MAIN BOARD REMOVING BACK 5V	SHORT IN HDMI IC (U501) DROPING power supply	REPLACING THE IC (U501) OR REMOVING IT AND LEAVING IT	H. Guimarães
PHILIPS	FWD789/55	Does not turn on, shows signal on display	Q906 short caused by glue	Glue cleaning and component testing	Junior de Conto
PHILIPS	14PT3131/78R	Turns on the picture for 5 seconds and turns off (either in Av or Channel)	Memory	Re-record or replace (in my case I replaced it and it resolved)	DTEC-ELETRONICA-Massapê-ce
PHILIPS	49PFG5001/78	IT TURNED ON NORMALLY, BUT AFTER ON AVERAGE 33 SECONDS, after showing an picture, IT TURNED OFF AND STAYED IN STANDBY WITH THE RED LED ON, WITHOUT BLINKING, IT SIMPLY TURNED OFF AND DOESN'T TURN ON AGAIN BY ITSELF. SO EVERYTHING INDICATES THAT IT IS REALLY AN UPDATE.	SOLUTION WOULD BE TO replace THE NAND FLASH MEMORY ALREADY RECORDED OR UPDATE WITH THE FILE THAT IS IN 4SHARED FOR THOSE WHO HAVE A NAND RECORDER. BUT OUT OF CURIOSITY I ACCESSED THE PHILIPS WEBSITE <a href=\"https://electronica-pt.com/su/1w\" rel=\"nofollow\" target=\"_blank\">External Link... < /a> and downloaded the software update that is tsound.	AND BY COINCIDENT I SAW THAT IT WAS AN UPDATE THAT SHOULD BE MADE IDENTICALLY TO THE AOC LINE, THAT IS, WITH THE FILE DOWNLOADED AND ON THE PEN DRIVE SHOWN ON THE TV, THE TV ON STANDBY, PRESS VOLUME +, HOLD IT DOWN, PRESS POWER AND KEEP PRESSED UNTIL THE STANDBY FLASHES OR OFF AND RELEASE VOLUME AND POWER AND THE TV DOES THE REST. DON'T BE SCARED, IT DOESN'T SHOW AN UPDATE BAR, ON THE CONTRARY IT JUST GIVES A FEW RANDOM BLINKS ON THE LED, AFTER IT GOES RIGHT THE TV TURNES ON BY ITSELF, REMOVE THE PEN DRIVE AND IT COMES IN BURN IN (GREEN RED BLUE WHITE), JUST ACCESS MENU AND CONFIGURE FACTORY RESET, READY, RUN FOR A HUG...	MIGUELTV
PHILIPS	48PFG5509	No picture but backlight on	Replacement of C715 with short on Tcon board		BHTECHCENTER
PHILIPS	TBM-C830	cd only plays the first 5 tracks	cd rotating motor tray	After replace the optical unit, it was necessary to lower the CD rotation motor tray a few millimeters, if you lower it too much the CD could scrape, I placed an old credit card between the motor and the tray and pressed it down.	jorgetec
PHILIPS	65PUG7406/78	Does not turn on standby off	C322 c328 shorted on main PCB	Replace c322 or c328
PHILIPS	42PFL7007	does not turn on at 3.3v from the power supply	q301 kst2907a defective		resistronic resende
PHILIPS	32PFL3606	Does not start, dead, with 3V3 of the STB	12V power supply, 24V did not work, L6599 replaced, PFC was also low, I removed and cleaned the glue from the reference resistors and it stuck at 390V.		Davi.sls
PHILIPS	58PUG6654/78	backlight access without picture	shorted capacitors on vcon	c95 left side of the vcon and c56 right side	DoorneL
PHILIPS	58PUG6654/78	backlight access without picture	shorted capacitor on vcon	c56 short right side of vcon	DoorneL