Philips Repair Tips
Search: philips
Results: 14241
Results: 14241
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
PHILIPS |
70PUG6774/78
|
Duplicate image after changing the board to another model | Transfer the U409 EPROM from the original board to the new board! Right tip from Leandro Sena | Tip passed on by rodrigo cofferi | Rodrigo cofferi |
PHILIPS |
40PFL3605 40PFL3606
|
Tv parada, sem 3v3 stand-by | D301 shorted. sb140 diode replacement | Antero | |
PHILIPS |
32PFL3404
|
Turns on with normal power supplys with inverter fault, lamps off | Ch1/ch2 | Replace the ch1/ch2 ceramic capacitor 1k | Medeiros Barbacena MG |
PHILIPS |
LE55U7970S
|
TV turns on, but the backlight blinks. | Defect on power supply board 715g8962-p04-000-003s. the resistor r8617 was altered. original value is 0.15Ω, defective it measured 0.5Ω. I inserted a 0.1Ω resistor and the defect was resolved. | rafaelmoraes99 | |
PHILIPS |
50PUG6513/78
|
I'm sound | Defect in audio IC AD87072 48 pins | Replace audio ci | Claudio Jorge Eckert Junior |
PHILIPS |
29PT9467C
SK5 1L CA |
Image closed on the side, reduced frame | Defect, replacement of cap c438, 272pf and bonina l432 next to the flyback | Dj pituka | |
PHILIPS |
43PFG6825/78
AF212121064147 |
Completely turned off, it doesn't even light up | 33k smd resistance connected to pin 5 of the u702 | José humbeto | |
PHILIPS |
32PFL5604
|
Does not turn on, the relay goes to the white LED. all power supply voltages are normal, but it does not bend pfc, | Cw2 (221k-1kv) with leakage. on the power supply board. | When replacing the TV it worked perfectly. | Real Eléctron Carvalhos MG |
PHILIPS |
FWM592
|
Turning off and heating r319 | Polyester capacitor c321 dry | Flavio | |
PHILIPS |
26PFL3404
|
TV only turned on backlight, checked power supply without 24v and 12v | 12v line in. short, check d911 if short, change and go for the hug!! | Dolly | |
PHILIPS |
42PFL3604
|
The 24v power supply burns out, after being repaired by the sector, it worked with a hissing sound on the t801. | It was the r859 0r47/2w. 0r47 2w "wire" resistor must be installed. the squeaking disappeared. the original is made of wire, but it burned. | Giovani Pires Bitencourt | |
PHILIPS |
42PFL3403
|
Red standby press power turns it off but it doesn't turn on..just disconnect cn7. and calling the pw tv called back with cn7 everything came back normal | Disconnect cn7 connect and return with cn7 everything was ok.. lucky for me... | Helio | |
PHILIPS |
FWP2000
|
32v power supply with 22v | Change r743 from 3k to 2k33 near tl smd and photo | Warley cesar | |
PHILIPS |
42PFL5008
42PFL5008 |
TV turns on normally with no image backlight on | It was changed in the service menu then it turned on normally without image backlight on | You have to rewrite eeprom 464rk 24c64 position 7705 near the network cable connector - download https://www.mediafire.com/file/ya43m9kd5kp6vqj/dados_eeprom_tv_philips_placa_42pfl5008_464rk__24c64.rar/file | neupsx4 |
PHILIPS |
20PT120 20PT122 14PT120
|
Doesn't tune in to the channel, it gets stuck | Eeprom defect [or enter service mode enter service mode by grounding pin 1 of the eeprom [or changing the memory with the recorded data[ | Go into service mode and check the addresses ho 1;al 1;po 1;ac 0 checking everything and just turn off the TV using the remote control and that's it | orlando lott |
PHILIPS |
PHG5301/77
|
No enciende stand by | Main board with fault | Replace main solders mi ro | Gordociri |
PHILIPS |
40PFL5606D/78
|
TV stuck on logo screen | Software update | The corresponding model was updated on the manμFacturer's website, following the step by step, I formatted the 2.0 pen-drive in fat and not fat32, inserted it into the TV and kept trying until it turned on, as soon as it turned on, the update screen opened and I did the update, I didn't go into settings but directly into the update screen, it was completed and worked normally. | Rapha_X |
PHILIPS |
42PFL3403/78
|
Philips 42pfl3403/78 stand by led blinks twice but does not turn on. | The TV turns on the stand by LED, accepts the power on command and after this command, press the channel + button when you can hear (very softly) the re1 relay engaging. At this moment, tsound was only a voltage of 3.3 volts because this relay had a bad internal contact. I dismantled the relay (it can be dismantled) and saw that the terminals were very far apart and that's why it armed but did not conduct (and the docking sound was very low). All I had to do was clean and twist it to bring the contacts closer together and the TV started working again. normally. | littlecarlos | |
PHILIPS |
42PFL5508
|
Turns off doesn't work at 110v. Sometimes it doesn't turn on | R9319 1.5m (cleaning) ic9301 (0133e) | I put ci spc7011f. working perfectly. | ELETRÔNICA FBS |
PHILIPS |
14PT3131/78R
L03.1 |
Turns on and then turns off | Tube blur protection | Put three 4148 diodes with + on the tgb filament and the - connected to the blk, then just look for the focus and move on to another | Eletronicazetec |