☰

Philips Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philips
Results: 14243
Make Model Symptom Problem Solution By
PHILIPS 20PT4331
Then turning off Add 3 diodes to the tube plate to bypass the tube in the ik circuit Put diode and solved orlando lott
PHILIPS FWM6000
Lowering the volume alone Fan doesn't fire In my case, it was the damaged fan drive transistor Stiltec
PHILIPS 32/42PFL3007D/78
Hdmi doesn't work Regulator u701 with 4.2 volt output. I changed it and the output went to 3.3. I was lucky I didn't burn the HDMI ci. Before changing the HDMI IC, check its supply voltages. RDS
PHILIPS AS 405
Power led does not light Just give it a touch Fredy
PHILIPS 43PFL3707D/78
Shutting down, it crashed on startup Regulator u701 g1084-33tu3uf, 3v3 regulator varying voltage between 3v6 and 3v7 Replace the regulator and add the c719 220μF 16v, go for the hug Valdecir Schena
PHILIPS 32PFL3606
Resistor next to the indication k1 with a value of 750k/smd You are giving tips without even checking the model, this solution described is for model 32pfl3605 and it does not work for 32pfl3606, pay more attention to what is posted without checking the correct model guys
PHILIPS FW-C505
I'm sound 7501 tda 7468d ruim To replace Adriano
PHILIPS 50PUG6513/78
50PUG6513/78 		Does not turn on, no standby. Shorted mosfets and blown ceramic capacitor Power supply board 715g8967-p02-009-001s with the power supply board fuse open (5a-250v) replace but first replace the 02 mosfets q9102 and q9101 (k10a50d) and the 02 ceramic capacitors that sit on top of them 101k 1kv MARCO BORSATO - MEDTEC INFORMATICA
PHILIPS 47PFL4007G-78
Turns on in a few seconds turns off to turn on again you have to wait a while Altered or faulty 3.3v regulator u701 g1084 -33
PHILIPS 14PT3131
Turns on and when the image appears, it turns off Resistors 3443 and 3444 of 1r presenting 6r each Replace Eliel Magno
PHILIPS 14PT3131
Turns on and when the image appears, it turns off Resistors 3443 and 3444 of 1r presenting 6r each Replace Eliel Magno
PHILIPS 14PT3131
Turns on and when the image appears, it turns off Resistors 3443 and 3444 of 1r presenting 6r each Replace Eliel Magno
PHILIPS 40PFH4100/18
TPN15.1 ELA 		The STBY LED turns on and does nothing else. No reset voltage. Substituir o ic u410 na main board. jose almeida tavares
PHILIPS 32PFL3404
It turns off in a few minutes, sometimes tsound is a beep from the speaker, it does not obey commands from the remote control or the TV. Cause: accumulation of dirt/grease/moisture on the RF board (signal) Clean the RF board with alcohol, pay attention to wsound the shielding is. Jose Magalhaes de Oliveira
TV PHILIPS 14PT519A
PT 		Sometimes it stays on for 20 minutes then it doesn't turn on but It stays on for 20 minutes when it turns off then it doesn't turn on but it's cap 2411 and 47 for 25v Arly
PHILIPS 55PFG5100/78
TPM15.3L LA 		LED blinking (flashing) LED power supply with low voltage, around 32v: c8108 with leak C8108 capacitor replaced IRIS CARLOS
PHILIPS 40PFL3606
No image, below the oscillating stripe appears, if the t-com heats up the problem ends Replace smd capacitor (very small) above 240k smd resistor (it is just above the ci of 5 terminals a1, close to ci 7j00), note: I don't know the value I left without, it must just be a current filter reginaldo moronte,eletronica junior caldas novas
PHILIPS 231TE4L
M715G5440-MOD-000-050 		The TV turns on and the Philips logo appears and turns off but the TV remains on with the 16v voltage changed to 19a20v Replace the tl431 and the photo coupler in the power supply o (ic 902) and o (ic 903 ALVES TEC. ELETRÔNICA CAMARAGIBE PERNAMBUCO
PHILIPS FWM912/BK
Turns on and off immediately, red LED on. Q7506 (bc847b) with leak on the overvoltage plate. Replace it even if it measures well. JMS Eletrônica
PHILIPS 50PFL4008G/78
TPS10.1L LA 		It doesn't turn on...not even the stby lights up. 5v power supply ok and if you arm the power supply all voltages 12 and 24v appear. 5v arriving at the input of the u703...absence or deficiency of 3.3v voltage at the output of this transistor.. Replace the regulator transistor (u703) with another equal one with a fixed value at 3.3v evando viana