Philips Repair Tips
Search: philips
Results: 14206
Results: 14206
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
48PFG5509/78
|
No image | Capacitor on tcom c08 board | Thank you jesus.. | Eletrônica ideal.. Mauriti CE |
| PHILIPS |
42PFL 3608/78
|
TV sometimes turns on sometimes doesn't turn on | Changing the capacitors next to the c593/c532/c532 crystal. You can also change the capacitors under the processor protection cover... the TV is working again and looks great.. | Just replace capacitors next to the crystals and next to the 10μF/16v processor | Kenzo gaucho |
| PHILIPS |
47PFL3007D/78
STPM9.1L LA |
It has a standby power supply, but when it turns on tsound is no 12 and 24 volt power supply | Ic9101 exploded | Replace; ic9101 ld7523gs, r9101 0.43, q9101 p10nk70, d9106, r9133 100, r9143 220, r9145 470, r9331 2r4, | Jackson |
| PHILIPS |
47PFL3007D/78
|
Turn on the voltages at the power supply are normal, but tsound is no audio and the screen does not light up. | Defect on the main board 715g5172-m01-001-004n, I reflowed the chip, it worked but then it stopped working. | I replaced the board with one from the 42" TV with end k, it worked fine, good luck. | Eronaldo(erontec) |
| PHILIPS |
FWM663X/78
|
Turns on, no sound, power supply voltages are ok 40v-0-40v | Red glue typical of this device, it changed the value of the 100k resistor r757 that goes to the base of the transistor q709, this circuit forms the oscillator of the circuit | Remove the infernal glue that Philips put on these devices and replace the resistor, tip applies to any component immersed in this glue | Lucho Electronics |
| PHILIPS |
43PFG5813
|
Does not obey control | Capacitor smd | Remove capacitor c211 from the control PCI | Brackmann |
| PHILIPS |
40PFL3606D
|
Gray image with vertical and oscillating lines, one side of the image darker, typical tcon or screen defect | Defect on the board tcon SMS resistor 3j22 (in the body is 1002) of 10kΩ, this resistor on the left side measured 34 volts after repairing the TV. | Replace resistor 3j22 de 10.000Ω ou 10kΩ ou 10k | MIGUELTV |
| PHILIPS |
32PFL3606D
|
Doesn't start | 1.8v oscillator did not work | Replaced 1.8v 7124 oscillator | Lucas Venzke |
| PHILIPS |
32PFL3606D/78
32PFL3606D/78 |
Turns on, works for a while and turns off | Cause: cold welding on transformer | Resolder the transformer with new solder and check the entire power supply board by cold soldering | Jonni |
| PHILIPS |
PHG4900/5000 78
|
Main inoperative with 12v ok | Defect: ic u706 jr4yi (sy8104adc) | ELETRONICA BRAMBILA | |
| PHILIPS |
40PFL5606D
|
Doesn't start | Keyboard | This keyboard is critical in this model. I disconnected the yellow wire from the 1m20 connector (position 8). The TV will work with just the remote control, without the need to replace the keyboard. will avoid other defects such as random channel restart | Lucafer |
| PHILIPS |
42PF7321/78
|
Plug in the socket, the stand-by LED on the 8001 board blinks until it stabilizes, check c8015 and c8016 1500/10v were at a low value. | I replaced both with 2200/16v and the LED stabilized. | Eronaldo(erontec) | |
| PHILIPS |
42PF7321/78
|
Plug it into the socket, press the power button, the LED flashes and doesn't turn on, sometimes it doesn't turn on. | Check c8075 470/10 had capacitance, low replace is normal. | Eronaldo (erontec) | |
| PHILIPS |
42PFL3604
|
Stopped working, power ok | C101 1000uf/16v dry and c474 4.7uf/16v in c474 be careful when removing the old one it can break the tracks | fabiusmax | |
| PHILIPS |
42PFL5508G
|
Turns on, the logo appears, gives a blue screen and restarts. | Corrupted software | Replace eprom or rewrite (I suggest changing) | Mau3000 |
| PHILIPS |
32PHG5201
|
Doesn't start | No voltages on the cn9101 jack. diode d9102 (sr515) shorted, q9101 open (k8a65d) and resistor r9101 (vm /lilaz/prata) open. | Replace them all. check voltages. | BICHARA SARQUIS |
| PHILIPS |
55PUG6700
|
Dead TV won't turn on. power supply with all voltages. board processor heating up normally, optical audio output with light. voltages in the main apparently ok. Even so, it doesn't generate an image | TV does not turn on - place the hob in an electric oven or oven for 10 minutes at a temperature of 280 degrees. obs. I only added this tip 120 days after the procedure and so far the TV is normal. | GUSTAVO STEFANON | |
| PHILIPS |
46PFL3008D
|
Turns on standby flashes backlight and returns to standby | Remove memory plug in...turn off clean and resolder memory | Whatsapp- (13)99613-2582 | Betonelli |
| PHILIPS |
14PT3336
|
League without image | 27k 3449 open resistor | Replacing the 27k 3449 resistor | RODRIGO CELL |
| PHILIPS |
40PFL
|
The LED stays on | See sw voltage that goes to the micro 1 volts | adelcio |