Philips Repair Tips

Search: philips
Results: 14238

Make	Model	Symptom	Problem	Solution	By
PHILIPS	55PUG6700 55PUG6700	Does not turn on, no standby.	Cap 471k 1kv leakage in the power supply primary	The primary fuse was open, I measured the entire power supply and didn't find a short, so I replaced the fuse, the TV turned on, but when turned on, the primary capacitor 471k 1kv started to heat up and burn, so I replaced it with one of the same value 471k 1kv and problem solved.	MARCO BORSATO - MEDTEC INFORMATICA
PHILIPS	42PFL3707D78	Turning off after some time and at 220 it doesn't turn off.	16v zener diode with leakage when heating at power supply position d9103	Replacing it and it can be a pth considering that smd is not always easy on the market.	Ademir
PHILIPS	29PT554A/78R	The control indicator just flashes red and does not allow a program	Every time you turn it on everything goes back to zero and the screen goes dark		Luis Eduardo Braga Volpi
PHILIPS	32PFL3707D	No voltages at the power supply (0v)	Dz9101 22v zener		Alextecnico
PHILIPS	32PFL4017G/78	Turns on normally and everything works, but after a few minutes the button controls stop working and go	Corrupted firmware	Rewrite memory 24c128 u409	GABSENS
PHILIPS	20PT4331/78 R	Turns on with horizontal lines above in RGB, vertical almost completely closed, turns off when it gets hot, and the sound fails	I changed the 2460 250v capacitor using Edson Peixoto's tip and the TV was normal in the tests;		Marcio
PHILIPS	42PFL3403	Does not turn on, short to c209.	Replace c209, if it does not oscillate, replace u201. If after changing, it arms, disarms and the red LED flashes, check the zd203 zenner diode.		electronicssupplyparts - Gramado/RS
PHILIPS	FWM 6500	Device turns on, but tsound is no audio	After a detailed analysis, I found some tips on the internet from other friends in the area, I didn't find anything to be replaced, I just cleaned a flat cable connected to the CD board.		Led Eletrônica
PHILIPS	40PFL6615 552 1 LLA	TV after being on for a while turns off or has the standby light off and does not respond to commands	Tantalum capacitor fp221 2.5 (100mf x2.5v which is located on the bottom of the board close to the processor position 2s29	Changing the tantalum capacitor looks like a diode but not the value of the cap is 100mf x2.5v or another approximate value in general 150mfd you can find in video game or notebook scrap.	ricardovideoesom
PHILIPS	40 /46 552 1LLA	TV works and for some time after turning it on, sometimes it doesn't respond to commands and the stanby light is off	Tantalum capacitor fp221 2.5 position 229 under the board close to the processor it looks like a diode but it is not	The correct thing to do is to put another tantalum capacitor in place, 100mfx2.5v, you can find it in video game or notebook scrap.	ricardovideoesom
PHILIPS	39PFL4707G/78	Inoperative, does not turn on, normal power supply voltages	Regulator in position u701 with problem, killing the 3v3 voltage.	Regulator replacement. the original is a g1084, but you can put an az1084 too.	Tiago C. Neves
PHILIPS	220TS2L	Poor quality sound	Reg 3.3v on main board	Regulator replacement	Eletrônica Bianca Ipirá
PHILIPS	42PFL4303/78	No 3.3v from standby after changing q601 and resistors.	Replace q150(kst2222a npn.)	Replace q150(kst2222a npn.	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	39PFL3008D/78	Image shaking, isolate the last 3 or 4 pins of the left flat cable on the left vecom!	It doesn't turn on, the red LED doesn't come out and all voltages are ok, heat up the eprom to the point wsound it loosens and turn on the TV with the eprom hot, with it turned on, reset	Rodrigo cofferi	Rodrigo cofferi
PHILIPS	FWP2000/78	Turns off after a short time on	In my case I changed all the capacitors and it didn't solve the problem! The solution was to change the tny277pn	Replace tny277pn I put a tny178pn and it worked rodrigo cofferi	Rodrigo cofferi
PHILIPS	40PFL3605D/78 40PFL3605D/78	Does not turn on, no standby.	C502 (ceramic cap 1kv 220pf) blown, q501 (mosfet fqpf6n80c) changed	Replace c502 and q501	MARCO BORSATO MEDTEC INFORMATICA
PHILIPS	32PFL5605D	Turns on, backlight turns on and no image	12 volts missing from the display	According to a friend's tip: electronicssupplyparts - lawn/rs, just complementing the tip with a better location of the damaged component, it is the i.c in position 7kfe, top side of the main board, looking at the board on the upper left side close to the large 6r8 coil (position 5kfa)or upper left side close to the .i.r cable 1m20	MIGUELTV
PHILIPS	32PFL5604/78	Does not turn on, standby LED stays on. doesn't blink	Capacitor c474, 4.7uf, close to a crystal on the main board, replace without measuring		Rogerio Novaes
PHILIPS	NTX400 NTX400X/78	Does not turn on, only blinks LEDs after adding power key	Q10 fet on the main board open, it is on the 5v reset line.		Rogerio Novaes
PHILIPS	39PFL4707G/78	After recovery of the power supply by unloading, operating normally open, when closing it turns on without image backlight on	Lvds cable passing close to the thread for wall support, when tightened it pressed and shorted out the housing.	Luckily tsound was no damage to the display, the wires were insulated with insulating tape and the cable was fixed away from the wall support area. good luck