Sharp Repair Tips

Search: sharp
Results: 1784

Make	Model	Symptom	Problem	Solution	By
SHARP	LC-80LE632U	TURN OFF BY ITSELF	PSU DEFECT	REPLACE TNY274PN AND 22R RESISTOR	GABSENS
SHARP	LC-42SV32B	Does not turn on, no standby	Check the components	Capacitor da fonte c9353, diodo zener 6,8v zd116, fusistor fb 707
SHARP	LC-32A28L	Does not turn on, no stand-by	Ic931 at power supply	Replace ic931 (tny277pn)	Brackmann
SHARP	21LF2A 21	Only turns on red light	Power supply		Jordão
SHARP	LCD-60LX540A	How to clear memory protection after 5 times on/off	1.remove AC power supply;2. On the TV, press & hold av/tv & vol- and turn on the ac power.3. wait until the display lights up.4. the letter "k" appears on the display, it means that the TV is in "factory mode". the volume + and - have only two levels 15 and 30.5. press both buttons at the same time vol+ and vol-. 6. on the remote "down " and "up" to access the second page. 7. use "right" and "left" to change the country. 8. turn off the TV, wait 30 seconds and turn it on again.		Andreas
SHARP	LC-52R64B	Stuck without image, with green LED on, and power supply relay beating. red LED on the main board flashes 15x.	Solved by the bga microprocessor on the main board.		rafaelmoraes99
SHARP	32LE144	Em stby	Measuring the voltages I found an output of 2.6 volts on the ic u3 and the service manual indicates 1.8 volts. The computer and nand memories were getting very hot.	I replaced the IC U3, the voltage returned to 1.8 volts and the TV worked normally.	Jose almeida tavares
SHARP	C1453	White screen without characters	L851 on the cinespocio plaque.	I didn't have one, I added a 22r resistor and it worked without any problems.	Francisco Melo eletrônica M.F
SHARP	LC42SV32B	After working for a while, vertical lines appear only within the images (not on the entire screen), then everything freezes and goes dark or the screen remains in a single color	T-con board defect	Replace the board	TULIO UBERABA
SHARP	C14R12	Vertical closed 2 fingers in the middle of the screen.	Bad contact on regulator ic604 7809	Remove the solder from the pins and solder, never resolder over the old solder.	Fernando Alcantra
SHARP	C14T51	Yellow with blue color in bar generator.	Ic801 tda4661 faulty.		Fernando Alcantra
SHARP	C14T51	No characters, no h-sync signal on pin 26 of the computer	D609 shorted		Fernando Alcantra
SHARP	LC-46R54B	Doesn't start	Ic7905(tny264pn),capacitor cy7008, resistor r7914( aberto)	Credits... guilherme alessandro	Guilherme Alessandro
SHARP	LC-32R24B	Does not turn on, green LED flashes quickly without stopping, only bu voltage +5v, tsound is no voltage on the capacitor c7129 (doubler)	Defective bulbs, test to identify (turn on, wait a few seconds and then press input + power for a few seconds, the LED will turn red and then the screen will light up quickly, proving that the bulbs are defective	Replace light bulbs	CDS_DIAS
SHARP	C-1438	Doesn't start	Capacitor c-721 1000uf 25v	Replace capacitor	Eudes Viana
SHARP	LC-22LE250 LC-24LE250 17MB95S 17MB95	Staying in stand-by, no start	Short in vcc		Rui
SHARP	LC-22LE250 LC-24LE250 17MB95S 17MB95	No backlight, led is normal no picture	Check/replace q10 and q11		Rui
SHARP	21LFG1BZ	It doesn't turn on, just standby is on and the power supply voltages are normal	The leaky taks dropping the 5v voltage in them, change them all	Replace tasks	Jr eletrônica
SHARP	LC-60LE632B DPS 165HP 2A	Doesn't start	D 7906
SHARP	C-20R12	Vertically closed when cold. after a few minutes it opens.	C206	Replace c506 1000µ 35v	MarceloPiranga