Sharp Repair Tips
Search: sharp
Results: 1785
Results: 1785
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SHARP |
C2010
|
130v zener shorted, removing it from the circuit and turning off the horizontal output you see that the power supply has more than 130v, if you insist on turning on the output, that's it. transistor d1397 burns | Supply capacitor c709 (2.2u/50v) exhausted | alisson | |
| SHARP |
C14T51
|
Cold turned on with horizontal tipping and hot didn't turn on. | R708 , (1.8megon) | When it didn't turn on, it made some tics, at the power supply (switched) | Alextecnico |
| SHARP |
C1453
|
Tries to start and is inoperative with irregular power supply up and down on the multimeter | The ceramic capacitor c719 shorted out, killing the diode 709, and as a precaution I replaced the electrol/high capacitors, the fly, trz h and vertical ci. Even though it was 14 years old, it looked new. | Berto | |
| SHARP |
C-20R12
|
If you press stand-by more than five times, it turns on. | Lag capacitor. 8n2 | 8n2 | johnny luis |
| SHARP |
C-29ST58
|
Tsound is no voltage at the power supply output | C-3723 shorted | Marcelo | |
| SHARP |
C-2017
|
Does not activate, power supply with 125v does not drop to 115v when activated | Zenner dos 33v | robson | |
| SHARP |
C-2017
|
Dark image | Resolder the wires connected to the kinescope socket, rgb e + b 180v and filament | guaracy borges | |
| SHARP |
C-2017
|
As soon as horizontal oscillator weapon disarms. | Change vertical output | guaracy borges | |
| SHARP |
C1417
|
Screen with an all red image, tsound was neither green nor blue, output with cold soldering. | Defect in the kinescope plate not working. | It was resoldered and that's it. | Armando de Olimpia Eletronica EvoluSom. |
| SHARP |
C1467B
|
Doesn't start | Horizontal driver transformer with open winding | After changing it, the TV started working again. | ELETRÔNICA CARLOS |
| SHARP |
C2038
|
Turning off | Troco do cp 606 7n5 1600v | julio.sertemaq | |
| SHARP |
2053
|
When turned on it turns off quickly | Ic 501 is defective, the 605 causes the TV to turn on, the defect is between pins 4 and 5 of ic 501, activating the protection | Replace ic 501 e ic 104 | Paulo tijuca |
| SHARP |
1413
? |
Burning horizontal outlet | Capacitor de bush | Replace bush width capacitor | edson ou tinho |
| SHARP |
20RS02
|
Tsound is only an image with an almost closed screen. If it enlarges, it becomes blurry and becomes a blue screen. | Disconnect pin 6 of ic202 and open the screen.resolved. | joaquim | |
| SHARP |
C-1440
|
Burning d 732 r2m | R731 33k changed | juci | |
| SHARP |
LC 32R24B
|
It doesn't work, it just flashes power and opc | Remove the power supply, place a 100r resistor on the 5v pin for stand by, 13v must appear | If not, I found a bad photo and a smd transistor q7110 I put a dta143 | |
| SHARP |
C-1453
|
Does not turn on normal power supply gives signal of oscillation and immediately goes into protection @@@ | C616=6n8x1k6 poliester | Help yourself, leave your tip ass. arni | EETRONICA ARNI-L. LEAL- SC |
| SHARP |
C-14S02
|
Does not connect all secondary voltages of the power supply without voltage b+ 0 @@@ | 1.8mega resistor in the primary power supply changed | Help yourself, leave your tip ass. arni | ELETRONICA ARNI-L. LEAL- SC |
| SHARP |
C-29ST54
|
Vertical closed | D501 open ta8427k short | Replace d501 ta8427k don't put ta8403k doesn't work | ELETRONICA MAURI JUNIOR |
| SHARP |
C2053
|
Turns on after turns off, sometimes it doesn't turn on | Capacitor 8n2 1k6 com problema | Replace the same | Jat Eletronica rs |