Cce Repair Tips

Search: cce
Results: 4824

Make	Model	Symptom	Problem	Solution	By
CCE	D4201 STILE	TV does not turn on orange standby LED	The standby LED turns orange without a command on the TV control, it doesn't turn on.. it should turn red and when turned on it turns orange and then green	Replace voltage regulator on main board u5 ld1117al 1.8 volts God bless the friends who posted this tip sound on the forum	Aguiar
CCE	HPS2185FS	Blue image far away with retrace lines	Resistor r922 15k in rgb open tube board	Replace 15k r922	beto2828
CCE	HPS-1471	A black stripe on the left side of the screen shaking	After a lot of head banging I found the r-414 open total 18 k resistor	Just make the replacement and that's it	ELETRÔNICA CAVALCANTE MARTINÓPOLE-CE
CCE	D3201	Flashing video	Cold solder trafo t1, causing variation in 12volts	Solve trafo	Diego Boeira
CCE	D3201	Flashing video	Cold solder trafo t1, causing variation in 12volts	Solve trafo	Diego Boeira
CCE	STILE D32	Turns on, turns off normally, lights come on and go off, the green LED on the power supply flashes and meets the normal control type	Switch power supply	Switch power supply	ASL ASSISTENCIA TÉCNICA TONINHO
CCE	STILE D32	Power LED does not light up	Change power supply	Replace font	ASL ASSISTENCIA TÉCNICA TONINHO
CCE	STILE D32	The stand by LED turns orange without command on the control, it doesn't turn on..it should turn red and when turned on it goes through the orange then green stage	Replace the main board	Replace the main board 1107314704	ASL ASSISTENCIA TÉCNICA TONINHO
CCE	D42 STILE	Intermittent image, with characters and audio (when changing channels it appeared)	And 19 (HD0837)	Replace	fbs eletronica
CCE	LN39G	Turns on normally, after a few minutes, the image disappears at the top of the screen. Give the TV a small tap on the right side edge and everything goes back to normal for a short period of time.	In my case, I dismantled the screen and saw 3 contact strips, on the right side of the screen. the middle tape was the cause of the problem, caused by the screw that holds the frame. Tsound's no point in just removing the screw.	You have to find a way to immobilize the tape in a certain position and fix it. or, replace the screen.	arock
CCE	HPS2185	It doesn't work and the LED keeps flashing	Flyblack shorted	Replace the flyblack	Vamir
CCE	LN244 MP113Q MP113Q	Does not turn on, low power supplys, with 0 volts	Z1 of vcc changed, stabilizing the ld7731 power supply at less than 10v.	After wasting a lot of time looking for bad components. I saw that the voltage was low. I put an 18 v zener (original y9 w 24v zener) and the power supply oscillated and turned on tvled.	Giovani pires bitencourt
CCE	D32 D32	Doesn't start	Replace capacitor 68mf po 400v ec16 ec11 and diode d18 high frequency	Replace capacitors at mains input and diode d18 at mains input/secondary power supply but not primary	gilson rocha
CCE	HPS 2097	Does not turn on, LED blinks 9 times twice and returns to STBY. The 33ufx160v capacitor was exhausted, it was replaced but it didn't solve the problem.	After much searching, tsound was a small flaw in the soldering of the d807 diode which, after being redone, the TV started working again.		Carlão
CCE	D3201	When turning on, you hear a buzzing sound at the power supply and it keeps turning on and off. tsound are all voltages (5, 12, 24v and stb), but it does not stabilize. backlight flashing.	Capacitor ec1 (100uf x 450v) with a "bubble"	Replace the primary power supply capacitor (ec1). replace without measuring. Take the opportunity to check the welds.	Pixel Assist
CCE	D32	TV turns on, green LED lights up, makes a noise at the power supply and stays with orange LED, no image	Defective t1 transformer	Just replace and move on to another	Welliton Campos
CCE	HPS2197	Pulling the image on the right side of the screen, with a white stripe.	C417 331pf 2v and r414 18k open	Replace c417 if you don't decide to replace r414	beto2828
CCE	LED24TV	Red LED lights up when you press the power LED changes to green and back to red	You u1	Solution adding a 220k 12v resistor to pin 8 of ci u1 in my case solved the problem.	Gilberto Costa
CCE	TV 2118 USP	Vertical closed	Ci vertical stv 8172a	Replace without forehead	CESAR
CCE	M-20T	Doesn't start	Defect in viper12a pwm power supply	I made an adaptation using a 12v 2a power supply and it worked without problems, I adapted the power supply to the product and everything was normal, lol	Adilson