Cce Repair Tips
Search: cce
Results: 4834
Results: 4834
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
CCE |
HPS2185
|
It doesn't work and the LED keeps flashing | Flyblack shorted | Replace the flyblack | Vamir |
CCE |
LN244 MP113Q
MP113Q |
Does not turn on, low power supplys, with 0 volts | Z1 of vcc changed, stabilizing the ld7731 power supply at less than 10v. | After wasting a lot of time looking for bad components. I saw that the voltage was low. I put an 18 v zener (original y9 w 24v zener) and the power supply oscillated and turned on tvled. | Giovani pires bitencourt |
CCE |
D32
D32 |
Doesn't start | Replace capacitor 68mf po 400v ec16 ec11 and diode d18 high frequency | Replace capacitors at mains input and diode d18 at mains input/secondary power supply but not primary | gilson rocha |
CCE |
HPS 2097
|
Does not turn on, LED blinks 9 times twice and returns to STBY. The 33ufx160v capacitor was exhausted, it was replaced but it didn't solve the problem. | After much searching, tsound was a small flaw in the soldering of the d807 diode which, after being redone, the TV started working again. | Carlão | |
CCE |
D3201
|
When turning on, you hear a buzzing sound at the power supply and it keeps turning on and off. tsound are all voltages (5, 12, 24v and stb), but it does not stabilize. backlight flashing. | Capacitor ec1 (100uf x 450v) with a "bubble" | Replace the primary power supply capacitor (ec1). replace without measuring. Take the opportunity to check the welds. | Pixel Assist |
CCE |
D32
|
TV turns on, green LED lights up, makes a noise at the power supply and stays with orange LED, no image | Defective t1 transformer | Just replace and move on to another | Welliton Campos |
CCE |
HPS2197
|
Pulling the image on the right side of the screen, with a white stripe. | C417 331pf 2v and r414 18k open | Replace c417 if you don't decide to replace r414 | beto2828 |
CCE |
LED24TV
|
Red LED lights up when you press the power LED changes to green and back to red | You u1 | Solution adding a 220k 12v resistor to pin 8 of ci u1 in my case solved the problem. | Gilberto Costa |
CCE |
TV 2118 USP
|
Vertical closed | Ci vertical stv 8172a | Replace without forehead | CESAR |
CCE |
M-20T
|
Doesn't start | Defect in viper12a pwm power supply | I made an adaptation using a 12v 2a power supply and it worked without problems, I adapted the power supply to the product and everything was normal, lol | Adilson |
CCE |
TV2118USP
|
Red image with retrace lines | After many tests I discovered a defect in the image tube | Replace the tube and run to the hug | Eduardo Santos |
CCE |
LED24TV
|
Red LED turns on, when you press power the LED turns green and returns to stand by again | Just looking at it makes a noise at the power supply as if it were disarming | D 11 replace without measuring because in the multitest it reported as good. | <small> |
CCE |
HPS2187
|
Open power supply repair r813 | GENIVALDO | ||
CCE |
HPS-2971
|
So fica stand by | Tran 804 | No gun | <small> |
CCE |
TV-2118USP/AV
|
Standby on, when you press the power key, the standby goes off and then comes on again. does not generate much. | Absence of 3v voltage on pin 30 of the micro, hout function. (h-drive) | R407/560r resistor replacement | Carlos Alberto (ELETRÔNICA BATURITÉ) |
CCE |
HPS-2185
|
LED wouldn't turn on, blinking and knocking relay | C426 470uf/16v dry | ELETRÔNICA POPULAR | |
CCE |
21US
|
Vertical closed at the bottom | Replace fr403 and fr402 | Rual de saja eltrônica R.e | |
CCE |
HPS-1403 C
|
No rainbow image | Resistor fr403 | Elias linardi | |
CCE |
HPS2991FS
|
The panel light takes a little while to flash, the light is not on continuously but flashes very weakly, b+ is very low and varies, q404 and q405 are broken, but I don't know if the customer shorted out these protection transistors or fpi because of the defect at the power supply. | The cause was the c816 470uf by 400v completely exhausted! | It was just a matter of changing it and the power supply returned to present the stable and correct voltage, the 2 protection transistors q404 and q405 were also replaced, which I don't know if the customer accidentally shorted these 2 transistors, because I think it's difficult for the power supply's main capacitor to be exhausted, cause these transistors to burn. | Fernando Elêtronica Millenium |
CCE |
2071 FSG
|
Turn on with the LED flashing but not the image | Replace kinescope board transistors | Wanderson |