Cce Repair Tips

Search: cce
Results: 4816

Make	Model	Symptom	Problem	Solution	By
CCE	HPS2185FS TODOS	Volume does not act but the bar increases and decreases	Replace q803 q802 solve q601 q602 q603 and solve resistor os I become the same		ED. ELETRÔNICA
CCE	HPS21AVP HPS2197C	LED flashes continuously voltage +b1 58v +b2 2v	Ic802 changed tl431		samuel leite
CCE	HPS-1471	Turns on with a vertical line and then turns off	Q 802 short	Replace of the same	AssisTec
CCE	HPS-1471	White screen with retrace lines	Resistor fr 901 e c 908	Replace of the same	AssisTec
CCE	HPS2971	Turns on after a while turns off when it's cold the power supply keeps pulsing	C868 on the capacimeter shows normal capacitance direct switching	Component replacement c868 1000 μF x25v	BETO ELETRONICA ACRELANDIA AC
CCE	LK32G	Turns on flashes black light quickly and turns off	Eprom	Re-record	Eletrônica Possamai
CCE	LK42D	Blue LED is on but when turned on tsound is no image	I tested the LED bars without opening the TV, they lit up through the connector but I was suspicious and opened the screen, tsound was a bad LED in one of the bars	You have to open the screen, in some cases you measure without opening it, it lights up, but it only takes 1 of them to open or short out to activate the circ. of protection.	VICTORINO
CCE	LK32G	It doesn't turn on... the voltage of 5 volts is normal... I noticed when activating the pow-on, that the 12v was low.	TL431 regulator leaky...this one is connected to the 12v line through an SMD resistor.	Touch the regulator! and run to success!	José técnico
CCE	LK42D	Turns on and off +- 10sec (goes into protection)	R 15 10k , por 100k
CCE	LK32D	Turns on and off +- 10sec (goes into protection)	R 15 10k , por 100k
CCE	LV40G	Has sound without image	This is mp3394	Replace the same ic 500	cleberlima rs
CCE	HPS1407	Image flickering with retrace lines, even with screen set to minimum	Fr901 22r changed on trc board	Replace fr e tbm c908 elt 22μF/250v	Zé Mário
CCE	HPS1497	Turns on by itself, changes volume	Escape key button	Replace for new	JEAN
CCE	HPS2971	I'm sound	C661 shorted	The sound output IC did not make any noise when touching its terminals. the 23v supply reached the msm but the 22v feedback did not. It was found that the c661 was shorted, it was enough to replace it to return to normal operation.	Emerson Iran
CCE	HPS-1471	No chroma, (color) black and white image.	Cristal (x701) 12.000 mhz	Replace crystal (replace)	Severino Silva
CCE	HPS-2071	The LED does not turn on, after pressing the power key, the LED flashes and returns to stand by	Capacitors of 4ufx160 and 33ufx160 dry but not swollen, after replacing the LED flashed quickly when turning on,	Following the tip sound on the forum, after checking protections, I removed jamper jc11 near the flyback and resolved, moving on to the next	Rodrigo V F
CCE	HPS2991FS	Stand by LED is lit but does not flicker	He sucked, he sucked	Replace it and give glory to God!!	Abençoado
CCE	29 USP	Turns on then turns off, returns to standby 3 times	Q802 q805 both bc337 can use bc 547 instead, and run for the hug		Soni luiz
CCE	STILE D32	Led power-on orange access	1.8v u5 regulator on the main board. position close to the processor.	Replacement with another taken from a scrap plate. It worked for hours and didn't cause any problems again. Note: the plates were very dusty, I did a general cleaning, as this may have been the cause of the problem. hugs to everyone, stay with God and don't forget to send tips, they are of great value to us technicians.	Anísio H
CCE	D40	It freezes completely when tuning to digital channels, otherwise it works normally...	U5 regulator replacement	Replace the u5 regulator, replace it without measuring... it gives 1.8v but for some reason it freezes... after changing the TV it will operate normally again.	Silviocuritiba