Cce Repair Tips

Search: cce
Results: 4824

Make	Model	Symptom	Problem	Solution	By
CCE	HPS1497	Turns on by itself, changes volume	Escape key button	Replace for new	JEAN
CCE	HPS2971	I'm sound	C661 shorted	The sound output IC did not make any noise when touching its terminals. the 23v supply reached the msm but the 22v feedback did not. It was found that the c661 was shorted, it was enough to replace it to return to normal operation.	Emerson Iran
CCE	HPS-1471	No chroma, (color) black and white image.	Cristal (x701) 12.000 mhz	Replace crystal (replace)	Severino Silva
CCE	HPS-2071	The LED does not turn on, after pressing the power key, the LED flashes and returns to stand by	Capacitors of 4ufx160 and 33ufx160 dry but not swollen, after replacing the LED flashed quickly when turning on,	Following the tip sound on the forum, after checking protections, I removed jamper jc11 near the flyback and resolved, moving on to the next	Rodrigo V F
CCE	HPS2991FS	Stand by LED is lit but does not flicker	He sucked, he sucked	Replace it and give glory to God!!	Abençoado
CCE	29 USP	Turns on then turns off, returns to standby 3 times	Q802 q805 both bc337 can use bc 547 instead, and run for the hug		Soni luiz
CCE	STILE D32	Led power-on orange access	1.8v u5 regulator on the main board. position close to the processor.	Replacement with another taken from a scrap plate. It worked for hours and didn't cause any problems again. Note: the plates were very dusty, I did a general cleaning, as this may have been the cause of the problem. hugs to everyone, stay with God and don't forget to send tips, they are of great value to us technicians.	Anísio H
CCE	D40	It freezes completely when tuning to digital channels, otherwise it works normally...	U5 regulator replacement	Replace the u5 regulator, replace it without measuring... it gives 1.8v but for some reason it freezes... after changing the TV it will operate normally again.	Silviocuritiba
CCE	29USP	Tracks on the left and right sides increase the sound, the tracks increase and waddle	Power supply+b without image 120v with image drops to 110v normal power supply has to give 130v	Replace r812 and r813 replace both	EDUARDO TV AV
CCE	2971	It turns on by turning on the key, the stand bay LED lights up, but when we press pawer the LED goes off and then turns off, remaining in stand bay mode again	Q 804 (bc 337-25) defective	Replacing the q804 (bc337-25) TV was ok.	Rdo Antônio Acre
CCE	LK20D	Washed canvas, or white.	Causes oxidized flat that goes from the LCD screen to the board. the defect is caused by wetting the television screen	Screen replacement.	Carlossbs
CCE	LED24TV	Turns on the green LED and turns back to red	Ci u1 on main board	Resolve if you don't decide to replace	beto2828
CCE	1418USP	Cce 1418usp tv with straight side black strip	C417 (331) 2kv with low value	Replace the same one for a new one, the problem is solved.	JP-ELETRONICA SANTA CRUZ RN JOÃOZINHO
CCE	2118USP NER2,2	Dark image	R430 and r 534 that feeds the tl 431 modified with high power supply		luiztvsom
CCE	HPS-2991V	League without image	D 910 and d 911 shorted on the kinescope board		Raimundo Alagoinhas BAHUA.
CCE	D42	Blue LED with red, does not turn on, all voltages ok, power supply board ok, keyboard board ok.	100uf-16v electrolytic filter capacitor at the output of the 1.8v LD1117 voltage regulator, from the main board, apparently good capacitor, but killing the 1.8v voltage dropping to 1.2v.	After removing the capacitor, the TV turned on normally even without the capacitor, but it was replaced and the TV is working beautifully.	jss_josafa
CCE	HPS2118USP	Cushion effect	Q406	Replace	Mauro Mascarenha Tel. (88) 981422821 Parazinho - Ceara
CCE	HPS2118USP	Cushion effect	Q405	Replace	Mauro Mascarenha Tel. (88) 981422821 Parazinho - Ceara
CCE	2918USP/AV	The TV turned on and gave an image release signal but tsound was no image, the screm increased but nothing did or appeared, tsound were filaments	I replaced the 102k ceramic capacitor in position c909 and the image appeared perfect		Francisco Melo
CCE	HPS-2171 34BI	It has OSD but no image	Resolder or replace c424		MARCELOPIRANGA