Cce Repair Tips
Search: cce
Results: 4824
Results: 4824
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
TV-2118 USP
|
Cushion effect | D409 | Replace | Mauro Mascarenha Tel : (88) 981422821 Parazinho - Ce |
| CCE |
TV-2118 USP
|
Excess width | C437 de 56nf | Replace | Mauro Mascarenha Tel : (88) 981422821 Parazinho - Ce |
| CCE |
TV-2118 USP
|
Horizontal closed with just a line in the middle of the screen | 330nf c429 | Replace | Mauro Mascarenha Tel : (88) 981422821 Parazinho - Ce |
| CCE |
TL800
|
Doesn't start. only 5 volts and power on, tsound are 12 and 24 volts. | D8 (stps20l60ct (screwed to heatsink)) bad. only detectable at x10k scale. replaced by fch20a10 (due to lack of original). | Eletrônica R-Tec | |
| CCE |
TL800
|
Doesn't start. only 5 volts and power on, tsound are 12 and 24 volts. | D8 (stps20l60ct (screwed to heatsink)) bad. | Eletrônica R-Tec | |
| CCE |
2118USP/AV
|
No sound, doesn't even tune a channel image in normal a/v but no sound | A broken track on transistor q 101 that connects to line 102 | And just restore the track | <small> |
| CCE |
HPS 2198
|
Turns on screen flashing and changing colors | Cold solder near the micro resolder | Note: cold solder does not appear, resolder it anyway | GSAELETRONICA GRANJA CALOFORNIA |
| CCE |
LH42G
|
TV won't turn on, totally dead | Absence of voltages of 5v, 13v and 24v. only at 5vsc (transistor q4 on the power supply board with leakage between gate and power supply) | Replace the transistor or place a 22r resistor between vsc and ps on. | Ivan Bustamante |
| CCE |
HPS-2073
34BI |
LED flashes quickly and does not turn on | Transistor q403 | 3R | |
| CCE |
HPS-2971
|
Screen with closed sides | Open resistor r850 | Replace resistor r850 | Fofao |
| CCE |
HPS-21AVP
|
Alloy blue screen retrace lines | Resistor r 922 tube plate | Bobson | |
| CCE |
STILE D24 LED
|
Front LED is off, TV doesn't work | Dz801 18v shorted to the power supply | eletrônica valdecir | |
| CCE |
HPS2185FS
|
Does not turn on LED decreases brightness and lights up again | When connecting the cable to the network, the LED lights up and decreases in brightness as if it were blinking and the TV does not start, measuring the power supply voltages d807 +b 103v with 80v oscillating downwards and d808 +b 16v with 6v and oscillating downwards. After analyzing the entire power supply, I found a 1u x 100v capacitor c824 exhausted. I'm sending it because I can't find any advice on this in any forum. | Matões A. Técnica | |
| CCE |
HPS1471
|
Vertical closed and turns off | D402 | Valdenice | |
| CCE |
HPS 2185FS
|
The LED blinks but the TV doesn't turn on, it lights up and goes back to standby | Secondary power supply capacitor with 50v low voltage | Replace the c825 47m/250v and the 33 they work together | charles |
| CCE |
HPS 2185FS
|
Blinking led | Flyback | Replace of the same | charles |
| CCE |
TV2118USP/AV
|
Lack of width, reduced frame. | Chap. 100uf/160v elco broken, it is the filter on the +b line | jr_TEC | |
| CCE |
TV2118USP/AV
|
Black stripe on the right side of the screen. | Chap. of damaged disc ceramic in position c417 (330pf/2kv) | jr_TEC | |
| CCE |
D32
|
TV doesn't turn on and the MOSFET Q29 is burned out | Open led bar and poorly sized power supply resistor (r164) with a value of 10k wsound the correct one would be 6.8k, because with the led bar open, the protection circuit works by receiving a little more bit more on pin 5 of the ci bit3251 1.5volts causing the bit3251 pwm ci to stop switching and sending voltage above 75v to the LED bar, thus protecting the q29 mosfet. | After changing the resistor r164 (10k) for a 6.8k one (SMD size 0805), changing the LED or complete LED bar and changing the MOSFET Q29 AOD446, it started working normally again. | JOSE_ADAIR |
| CCE |
L2401
|
LEDs off | Cold welding in c 819 | marco.32 |