Cce Repair Tips
Search: cce
Results: 4816
Results: 4816
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
HPS 2992P
|
Dark band on the left side of the screen | C402 replacement of 331p x 2kv capacitor, following the tip from my friend Carlos Guerra | Lino Bugatty | |
| CCE |
HPS 2971
|
Turns on and then disarms | Tr smd posiçao q 404 | ozias borges pereira | |
| CCE |
HPS 2971
|
Turn on then turn off | Tr smd posiçao q 404 | ozias | |
| CCE |
HPS 2002
|
LED goes out, doesn't turn on, voltages ok | C410 = 471 | ||
| CCE |
HPS1405
|
It turned on stand by when the control was activated, it turned off but did not start | Fr 401 open | Just replace it | ELETRONICA CAVALCANTE |
| CCE |
HPS2971
|
TV starts and then returns to stand by | Note only TV with tube board with transistors in the video outputs | Little known component sg 902 903 or 904 shorted | EDEZIO ELETRONICA |
| CCE |
HPS2004
|
+b de 125v com 103v | R810 0r27-2w alterado na power supply | Replacelo | antonio nobrega patos pb |
| CCE |
HPS2991 FSC
|
No image dark screen | C-409, observe the flyback voltages if they are low, change the cap. | 50 in tea steam 21 in..... | ELETRONICA INFOAÇU |
| CCE |
LED24TV
|
Dark screen, LEDs don't light up. | Ec7 (100uf 50v) | Baguatech | |
| CCE |
HPS-2909
|
TV comes out of standby, does not generate high voltage and then returns to standby. | R403 open | This resistor is located under a black corrosive sticker and in series with the base of the q401 (horizontal drive) | Persio (TVCompany) |
| CCE |
HPS1471
|
Screen elevated, even when downloading everything on flyback | Fr404 open | Just replace | paial.eletros |
| CCE |
2918USP-AV
|
TV turns on and turns off | Sg902 in tube socket | Sg902 replacement | josnei |
| CCE |
HPS1497
|
No sound sometimes tsound is and sometimes not | Check sound output ic 601 | Replace the same | rolf |
| CCE |
HPS1497
|
No sound sometimes tsound is and sometimes not | Check sound output ic 601 | rolf | |
| CCE |
HPS2991
|
TV with screen off, voltages all normal, filament on. | It was the c421=47k-250vts short and the r423=1k on the abl line, I replaced the defective components and left for the hug. | ELETRÔNICA MELO-BOA VIAGEM-CEARA | |
| CCE |
TVS 2910
|
TV does not turn on with the 14v power supply measuring 10v and the 130 power supply measuring 100v led off | Defect was a 1n4148 diode in position d400 | Mário moreci | |
| CCE |
HPS 2991 FS
|
It doesn't turn on, and the standby light turns on very weakly. | Q - 804 (bc - 337) | Replace the same | BARRETO CRUZ |
| CCE |
HPS 1497
|
Doesn't turn on, relay keeps hitting and LED blinks | C 417 heating | Replace c 417 (331 x 2kv) | Eletronica valença |
| CCE |
HPS 1471
|
Device does not turn on. do not arm the power supply | Quick access to the solution to release the q-403 and q-404 (smd), tsound is no return. ditto for mod. 20" | ||
| CCE |
HPS1471
|
Vertical interference in the image | R-306,1r5-open | jps, eletr,c,grande |