Cce Repair Tips

Search: cce
Results: 4824

Make	Model	Symptom	Problem	Solution	By
CCE	HPS-2197FS	"cheeping" power supply, without voltages in the secondary power supply.	Flyback [bsc25-0226h] em cuto.	This flyback is practically impossible to find in stores, so I decided to try the tat2012 from cce hps 2007 and... all that was left was the filet, I just needed to adjust the focus. they can replace without fear.	Altevir Lima [Valparaíso Eletrônica/ Ananindeua- PA]
CCE	HPS - 1473	Turns on and off with closed vertical	Q802 prices	Replace	Mauro Mascarenha Parazinho - Ce
CCE 29"	HPS 2991 P 2991	Blurred image weak tube symptom	Weak tube	Replace l400 in the filament feed or jam it	Edson Caeté
CCE	HPS1471 =2071	Squeezing the pawer takes a while to turn on @@@	C-712 bad, replace without measuring		ELETRONICA ARNI / LEOBERTO LEAL-SC
CCE	HPS2005	No image with sound	It has all power supply voltages! it just doesn't oscillate horizontally	Bad horizontal transformer drive, replaced without measuring! the r411 that goes to the trafo is missing 27v!	orlando lott
CCE	HPS1471	Power supply does not arm nor does the LED light up	18volt zener close to the power supply ci smd		edezio eletronica
CCE	HPS2991	No image normal voltages turbo with voltage	Small adjustment to the screen and changing the r442 a little changed and it works again		Denobie
CCE	2197FS H2197	When turned on, the LED starts flashing	I killed them both at once, it was also the flyback	I put the tat 2012 resolved score 100	luiztvsom
CCE	2071 2071FS	LED blinks and stops and stays on	Fleyback	I didn't have the bsc25-0206f sound, I put the tat 2012 and it worked perfect	luiztvsom
CCE	HPS2092	Tsound is a dark band in the left corner of the screen approximately 1 cm, image shifted to the right.	Defect in the line that connects to pin 1 of the fly that goes to the sandcastle point of the ic501, changing c410 = 100pf resolved the defect.		Bruske
CCE	HPS1471	Turns on and off 3 to 4 times and goes back to standby	Fr402 open on +12 line	Replacement	Eliel Magno
CCE	HPS 14R	It doesn't turn on or the LED lights up.	Printed broken underneath the solder connected to the o2 pins of the tf - 802.	Clean and resolder	BARRETO CRUZ
CCE	HPS 2991FS	Turns on, and the vertical keeps wanting to close.	Replace s m d (q 404 - bc 856b ) e o ic 301 (tda -8359j)	Replace the same	BARRETO CRUZ
TV CCE	HPS 21AVPVALTER	Turns on, skips the channel, with a banner on the right side.	On/off micro switch. + capacitor 417 330p 2kv		valter
CCE	HPS2991	With audio without video, just turn it off by unplugging it	C 901, on the tube plate		preá-rs
CCE	HPS 14R HPS 14R	Turns on, lights the filament and the screen is completely off, excites the scrim and nothing.	Change the video card capacitor (102) or 1k. So guys, just run to success.		Luis Pacheco
CCE	HPS2991 0000	Unstable image, screen voltage varying.	I did a check-up on the abl and all the compts were ok	I made a parallel bridge to reinforce the signal at the stage, placing a 47k resistor on pin 54 of the micro to the abl pin of the fly. It was cool!!! good luck!!	Jhone Eletronica
CCE	TV2118USP	Vertical closed -	Transistor v541 short - after the vertical replace it opens but tsound are upper lines and v541 overheating. change diode of this power supply		Master Eletronica
CCE	HPS-2199FS	Black stripe on the left side.	C417 (330pf/2kv) e r414 (18k)		Manoel (Noca)
CCE	HPS2185FS	Does not open completely horizontally (after changing the flyback)	D401 shorted - replaced		rtek1000