Cce Repair Tips

Search: cce
Results: 4834

Make	Model	Symptom	Problem	Solution	By
CCE	HPS1471	Turns on and off 3 to 4 times and goes back to standby	Fr402 open on +12 line	Replacement	Eliel Magno
CCE	HPS 14R	It doesn't turn on or the LED lights up.	Printed broken underneath the solder connected to the o2 pins of the tf - 802.	Clean and resolder	BARRETO CRUZ
CCE	HPS 2991FS	Turns on, and the vertical keeps wanting to close.	Replace s m d (q 404 - bc 856b ) e o ic 301 (tda -8359j)	Replace the same	BARRETO CRUZ
TV CCE	HPS 21AVPVALTER	Turns on, skips the channel, with a banner on the right side.	On/off micro switch. + capacitor 417 330p 2kv		valter
CCE	HPS2991	With audio without video, just turn it off by unplugging it	C 901, on the tube plate		preá-rs
CCE	HPS 14R HPS 14R	Turns on, lights the filament and the screen is completely off, excites the scrim and nothing.	Change the video card capacitor (102) or 1k. So guys, just run to success.		Luis Pacheco
CCE	HPS2991 0000	Unstable image, screen voltage varying.	I did a check-up on the abl and all the compts were ok	I made a parallel bridge to reinforce the signal at the stage, placing a 47k resistor on pin 54 of the micro to the abl pin of the fly. It was cool!!! good luck!!	Jhone Eletronica
CCE	TV2118USP	Vertical closed -	Transistor v541 short - after the vertical replace it opens but tsound are upper lines and v541 overheating. change diode of this power supply		Master Eletronica
CCE	HPS-2199FS	Black stripe on the left side.	C417 (330pf/2kv) e r414 (18k)		Manoel (Noca)
CCE	HPS2185FS	Does not open completely horizontally (after changing the flyback)	D401 shorted - replaced		rtek1000
CCE	HPS2185FS	Does not turn on, LED lights up but goes into protection	Replace of flyback bsc25-0206h (shorted) + replace of tr hor bu2508dx (original is 1508) * note the FR401 can be open or with a cold solder (heats up)		rtek1000
CCE	HPS-2918USP	Image moved to the right side, and shadow on the left side...	C-406 = 331/2kv .		ELETRONICA INFOAÇU
CCE	HPS2991 FS	It keeps ticking on the speaker and the LED doesn't light up. no standby	Photo coupler, change.		joaomvjr
CCE	HPS21AVP	TV turns on, turns off, then the relay keeps arming and disarming and protection comes on	Swap zd 807 8v2 open		ELETRONICA CENTRAL ITAPOLIS SP
CCE	HPS 2991	TV with LED on, did not flicker.	It was the d812 =sk4f, I replaced it and the TV worked normally.		ELETRÔNICA MELO BOA VIAGEM -CEARA
CCE	HPS2004	Led flashing fast, normal high supply, low oscillating at 8 volts	C812, I put 47mf / 63v		Alextecnico
CCE	HPS 1402B	Normal main supply, but the 103v is zero	C 812 weak. change without testing		KIN
TV CCE	HPS 2002	Intermittent on and off	Q 802 o bc 337 It's just replace		MARCIORVGO
CCE	HPS-2185	The LED flashes, the tube cannon lights up, but the screen does not light up	Picture tube	Replace it of course!	Marcondes Lima, Jaicós-PI
CCE	HPS 1491	No colors – normal b/w image	Capacitor c 505 (0.01 µf) with leakage	Replace	Eletrônica_Almiro