Cce Repair Tips

Search: cce
Results: 4834

Make	Model	Symptom	Problem	Solution	By
CCE	HPS-21AVP	Alloy blue screen retrace lines	Resistor r 922 tube plate		Bobson
CCE	STILE D24 LED	Front LED is off, TV doesn't work	Dz801 18v shorted to the power supply		eletrônica valdecir
CCE	HPS2185FS	Does not turn on LED decreases brightness and lights up again	When connecting the cable to the network, the LED lights up and decreases in brightness as if it were blinking and the TV does not start, measuring the power supply voltages d807 +b 103v with 80v oscillating downwards and d808 +b 16v with 6v and oscillating downwards. After analyzing the entire power supply, I found a 1u x 100v capacitor c824 exhausted. I'm sending it because I can't find any advice on this in any forum.		Matões A. Técnica
CCE	HPS1471	Vertical closed and turns off	D402		Valdenice
CCE	HPS 2185FS	The LED blinks but the TV doesn't turn on, it lights up and goes back to standby	Secondary power supply capacitor with 50v low voltage	Replace the c825 47m/250v and the 33 they work together	charles
CCE	HPS 2185FS	Blinking led	Flyback	Replace of the same	charles
CCE	TV2118USP/AV	Lack of width, reduced frame.	Chap. 100uf/160v elco broken, it is the filter on the +b line		jr_TEC
CCE	TV2118USP/AV	Black stripe on the right side of the screen.	Chap. of damaged disc ceramic in position c417 (330pf/2kv)		jr_TEC
CCE	D32	TV doesn't turn on and the MOSFET Q29 is burned out	Open led bar and poorly sized power supply resistor (r164) with a value of 10k wsound the correct one would be 6.8k, because with the led bar open, the protection circuit works by receiving a little more bit more on pin 5 of the ci bit3251 1.5volts causing the bit3251 pwm ci to stop switching and sending voltage above 75v to the LED bar, thus protecting the q29 mosfet.	After changing the resistor r164 (10k) for a 6.8k one (SMD size 0805), changing the LED or complete LED bar and changing the MOSFET Q29 AOD446, it started working normally again.	JOSE_ADAIR
CCE	L2401	LEDs off	Cold welding in c 819		marco.32
TV CCE	D3201	Activating the menu, volume and other games, a recurring problem with this model, changing the board is very expensive, so I used the following repower supply wsound tsound are front keys, I closed the jump between sk0 and sk1, you cancel the front and use it normally via the control and the LED stops blinking.	A jumper was made on the touch controls side plate, the LED stopped blinking and activating the functions, it is more viable than changing the main unit and using the cont. normally.		José delta line
CCE	LK42D	Turns off LEDs, (no damaged LED)	Change r15 to 100k		Diego Boeira
CCE	TV2918 USB-AV	The TV turns on, it has a normal high, but tsound is no image, sometimes by increasing the screen a little the relay hits and the image appears then you adjust the screen back into place and when you turn it off and on again the relay hits but tsound is no image again.	Make a jumper on the l400 coil, if that doesn't help, do a general resoldering on the focus board, especially on the harness that comes from the main board.		TALL-TEC Eletrônica
CCE	D3201	Turning on the red LED and pressing power didn't change anything.	I measured the power supply and the 5v standby signal and the ps on were normal	I measured the power button and it was open, replacing the power button.	Eduardo Luiz vinoti
CCE	HPS1402	Doesn't start. Sometimes the LED lights up and sometimes it doesn't	Open driver trafo		jr_TEC
CCE	HPS1471 34BI	Light blinking after clicking on	Find out by messing with the kinescope plate	I fixed it and replaced the socket under warranty.	genilson
CCE	HPS2171FS H214A	Turn on standby flasher with closed vertical	Q802 and q803 leaking	Replace the aforementioned transistors	Eletrônica Barros
CCE	HPS2991 FS	Restarting on off it stays like this on on off only	Q802 change without measuring if possible put the white face bc337	Q802 bc cara branca philips	asl
CCE	1420	Generated and then cut	Fr 402		Gabaglio
CCE	LK420	Power supply 2580 service mode	Power supply 2580		HP ELETRONICA