Search: cce
Results: 4824
Make Model Symptom Problem Solution By
CCE 4201
STILE
It doesn't turn on, it doesn't light anything. Defective primary. Identified several burned components Identified several burned components. ((q1 - mdf13n50), (f1 - 6.3 a), resistors r13a, r14a, r14, r15, r16, all (0r68 - 2w) and 2 smd resistors on the solder side, r18 and r19 of 4r7, after changing everything, the power supply turned on, but the lamps kept blinking and the pfc voltage was low (160v), when checking it was identified r 21 of 470r open., after the replace everything worked..... a lot of work to find, phew... . CDS_DIAS
CCE 14 HPS 1471
The lede ased is blinking quickly and does not connect to the tvlede LED flashing fast José hildo dá silva
CCE TV-2118USP/AV
FBT STD
Does not help Fr401 Replace the 0.47r resistor fr401 Sinailson furtado
CCE TV-2118USP/AV
FBT STD
Didn't care C417 e o c430 Replace the 331k 2kv c417 and the 222k 1kv c430 Sinailson furtado
CCE TV-2118USP/AV
FBT STD
This TV arrived at my electronics with the stand bay light turned off, but the TV turned on normally but without a normal image, sound and only the characters appeared on the screen without luminance. C424 Replace the 473k 250v c424, just replace it and run for the hug! Sinailson furtado
CCE HPS 2171
With image only on the av R104 and r103 smd of 100r on sda pins, and varicap scl MARCONES DE ARARIPINA-PE
CCE HPS14BSP
LED blinking when cold C812 47uf /25v in primary Replace without measuring Multi Service Eletronica juara
CCE CS-585 C
Volume acts on the display but the sound remains low and does not increase in intensity Q509 - bc337-25 open All it took was replacing it and the sound returned to normal. Mr Técnico
CCE HPS 14BS
Vertical closed when turned on, then protection enters After checking the vertical output, I diagnosed the 9v regulation with a problem I found res. r 823 10k open, connected to pin 4 of reg. ic 805 Imagem
CCE HPS 14BS
Vertical is closed when turned on and goes into protection After checking the vertical output, I diagnosed problems with the reg. 9v I found res. 10k r 823 open, connected pin 4 ic 805. Imagem
CCE HPS2097
Vertical closed at the top without +12v. C426, c425= 470uf 16v. no capacitance NILMAR
CCE HPS-1407
Does not tune channels The transistor q101 bc337-25 was shorted killing the 5v from the varicap Replace of the same ASSISTEC
CCE HPS29
It would turn on after about 20 minutes, then turn off and turn on again by itself. I replaced (c835 47uf 50v / c834 100uf 16v / c836 470uf 16v ) q802 bc337.25 q805 bc337.25. Replace the mentioned components genilson
CCE HPS2118
USP
Excess width Diode d409 mur460 shorted or altered. Replace diode mur460 position d409 Ricardovideoesom
CCE LH42G
TV won't turn on without standby Changing the +5v line capacitors PAIM ELETRONICA
CCE STYLE D3201
Does not turn on, voltage 5v low and varying R28 value 3k3 smd, changed to 1k3 PardalX
CCE C320
The LED does not turn on or light up Power supply rf filter coil (l1) Resolder the 4 terminals well reinforced. Lucafer
CCE C420 C390
It just turns on standby and doesn't turn on Ci those who u11 (ad52582a) HP ELETRONICA
CCE TV-2118USP/AV
Changes without sound Q602 ic101 Replace the ic101 and remove the q602 from the board and just run for hug! Sinailson furtado
CCE TV-2118USP/AV
Normal image without audio. Q602 Remove the Q602 from the board and the TV will work normally. God be praised! Sinailson furtado