Cce Repair Tips
Search: cce
Results: 4822
Results: 4822
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
CCE |
L244
|
Call, please wait | Memory replace | Replaced the memory, TV resolved | Fernando rj |
CCE |
HPS1471
|
Black stripe on the left side, as you moved the plate the stripe disappeared. | Chap. smd broken in the solder, I used a magnifying glass to desolder each one until I found the broken one | C405. | Joaomvjr |
CCE |
HPS 1403
|
Turns on standby, when the LED turns off but it doesn't turn on +b ok | I'm sorry | Replace the bc337 even if it's good | |
CCE |
DD8080
DD |
Defective automatic start and return, speed varying | Pci power supply: q101 q102 q103 q104 (bc 548a) r 114 - 4k7, r 116 - 8k2, r 117 - 4k7 pci controle: ic2 e ic3 sn7400n ic4 sn7410n | It arrived with the speed varying by 33 rpm, almost imperceptible, but it was varying downwards, and the arm did not move automatically, someone had turned off the arm's motor because they could not solve the defect, it went to the beginning of the record, went down and came back. for rest. Analyzing the diagram I saw that the arm control is done by ic 2,3 and 4, when changing, it worked normally, in terms of speed, I replaced all the electrolytics which were in bad appearance, yet it continued to vary, changing the resistors for new ones. speed became more stable, but still varied, the solution was to replace q101,102,103 and 104 without testing. | Trendset |
CCE |
D4201
MSD309D42 |
Does not tune to digital channels | Varicap room | As I couldn't find the varicap I replaced the main board. Putting in the new card gave an inverted screen. Replace the memory on the bad board with the good one. problem resolved or try updating the software. | Adriano Miranda |
CCE |
HPS1497P
|
Hitting relay and heating q802 | Dz807 8v2, e c 838 220/16v | GDP2 | |
CCE |
HPS1401
|
Does not turn on, voltages b+, 9.8.5 v ok, led off, pin 39 ic 701 with 0v pin 40 with 2.7v | Cause c 723 470mf . | GDP2 | |
CCE |
HPS-1471
|
Doesn't pick up channel, stays blue screen | Scl memory trail | I replaced varicap and it didn't solve the problem, I analyzed the scl and sda memory tracks and found the scl track was broken. | |
CCE |
TV-2118USP/AV
|
Turns on and off quickly, sometimes it works or not | V563 2sc2383 changed base x emitter | Replace | Hndrsn |
CCE |
HPS 1497
|
Does not turn on, LED blinks and lights up again +b normal. | Shorted or leaking capacitor, c410 of 101 (100pf), is on the side of the driver transistor q401. | After the replace everything was ok. | George Pontes |
CCE |
LT32G
|
Bus lighting very weak, switch ci voltages normal | Replace q4, with a small leak, heating beyond normal | José Moura | |
CCE |
TV 2118USP/AV
|
Turns on flashes direct led with image turning on and off directly with no functions, nothing operates, not even by remote control | Change all the ringtone keys and run to dim dim | eletronica publison natal rgn | |
CCE |
TV 2118USP/AV
|
Turns on flashes direct led with image turning on and off directly with no functions, nothing operates, not even by remote control | Change all the ringtone keys and run to dim dim | eletronica publison natal rgn | |
CCE |
HPS-1497
|
Blinking LED, won't turn on | Exhausted capacitors | Replace c825, e c829 | leo |
CCE |
STILE D32
|
Turns on normally with image, after a few minutes, turns off with green LED, backlight goes out and no audio, normal functions. | 1.8volt u5 regulator with leakage | Changing u5 and u3 without testing plus the 4 470 x 16 capacitors of these power supplys, it didn't turn off anymore. | Toni |
CCE |
LED24TV
|
The LED only stays red, it doesn't blink or anything | Bios | Rewrite eprom | Eletronica Jambeiro |
CCE |
HPS-2097
|
The LED blinks on and off, the LED stays in stand bay and does it all over again | Change the bc 337 both and run to dim dim | eletronica publison natal rgn | |
CCE |
STILE D3201
|
Sound like robot disappearing the sound | Replace capacitor next regulator 1.8v ec4 | Replace capacitor ec4 next regulator | Adao da central audio e video |
CCE |
TV-29USP
|
Turns on and off immediately, no image appears | Sidac sg903 short, red color, tube plate, test all three, replace and go for a hug! | HAHNRAHN | |
CCE |
HPS-1471
34BI |
Red (or other colored) spots on the screen | Ptc801 (positive temperature coefficient) com defeito | Just replace the part, do not use magnets to try to demagnetize it. After changing the part, the stains disappeared | Tiago C. Neves |