Cce Repair Tips

Search: cce
Results: 4824

Make	Model	Symptom	Problem	Solution	By
CCE	STILED 4201	Without sound and with "popcorn" in the sound	Defective ec4 electrolytic 470uf by 16v	Replace without measuring ec4	edmilsom pimentel
CCE	HPS-1471	Dark image	Resistors 208 and 209	Replacing the 2 47k resistors	Raimundo tec
CCE	STILE D40	Without image, with sound. the menu appears.	Replace reg. u3, 3v3 leaving 3v2.		joaomvjr
CCE	STILE D3201 MP320G	LED turns green but does not turn on lamps (backlight) tsound was no voltage of 12 and 24 volts	Diode d7 open: just change it and give the budget. It generates a voltage of 12 volts to power u5	Replace diode d7 in4007 with a more powerful one.	ELETRONICA SALES.NATAL RN
CCE	STILE 3201 BRANCA	No audio	Q 12 removes		C.M eletronica
CCE	TV 2918USP/AV	Does not turn on, LED is on.	C407 (3n3 ) c402 (331pf) r401 (18k) e q401 (mpsa42)	Replace c402 / c407 / r401 e q401	MARCONES DE ARARIPINA-PE
CCE	2918USP/AV	Does not turn on, LED blinks, and returns to standby.	Defective transistor q401 mpsa42	Replace q401 mpsa42	MARCONES DE ARARIPINA-PE
CCE	TV PH 42M	Just plug in a weak blue LED	Loosen the inverter board connector if the LED turns red, the defect is on the inverter board, in my case tsound was no shorted MOSFET	As I had another board and in a rush to save time I replaced the board, but this way it gives you a guide to know which board the defect is on.	Ariel Santos
CCE	HPS-1471 34BI	When plugging it into the socket and pressing any button, the LED would flash and it would not be possible to start.	Check primary, secondary, vertical, horizontal, and flyback power supply components	In my case it was the fr401 (1r for 1w, close to the flyback), I replaced it and the TV finally turned on.	Tiago C. Neves
CCE	HPS 1497	The image doesn't turn on, the LED doesn't stop flashing.	Faulty flyback, low voltage on scrin pin	Replace the same
CCE	STILE D32	At 220 volts it even lights up the lamps and gives an image, at 110 the lamps blink a few times and the power supply shows error 11 (11 blinks). defect in the primary power supply pfc	Q6 smd transistor in the primary power supply open, did not feed the u1 approximately 16 volts.	Replacing u6 (It's a pnp transistor)	MIGUELTV
CCE	2171 FS	This TV had the LED off and tsound was a strange noise at the power supply:	I changed the fly back and it solved the problem, I put the bsc25-0206h in and it worked. Help others and God will help you too;		ELETRONICA NOSSA SENHORA APARECIDA
CCE	2171 FS	LED doesn't turn on	Resistor fr 402 of 1Ω behind the fly back connected to diode 404.		ELETRONICA NOSSA SENHORA APARECIDA
CCE	LT32G	Don't tune in	Change varicap from another cce board that is a similar model ln32g, etc.		reginaldo moronte,eletronica junior caldas novas
CCE	TV 2118USP/AV	Low volume	R681 (smd) between the terminals of capacitor c666, remove it from the board	Remove the r681, smd, 22k from the board that is between the c666 terminals	MARCONES DE ARARIPINA-PE
CCE	TV 2918 USP/AV	Vertical closed at the bottom, and with lines on the screen.	C417, c424 and c428 amended.		MARCONES DE ARARIPINA-PE
CCE	TV 2118USP/AV	Alloy with closed vertical, at the bottom, and retraction lines	C417 c424 and c428 swap all.		MARCONES DE ARARIPINA-PE
CCE	TV 2918 USP/AV	Reduced frame, with lines.	Capacitors c417, c428 and c424, replace them all, and resolder them on the vertical output.	Replace c417 c428 and c424	MARCONES DE ARARIPINA-PE
CCE	HPS-2118AVP	Low volume	Q101( bc337/25 ) grounded! close to the varicap.	In my case, I thought it would be better to replace it with a Kia7805. I just had to remove the resistor r412, and connect the middle pin, directly to ground.	Marcones de Araripina-PE
CCE	LN244W	Doesn't start. Standby LED does not light up	Ec4 capacitor main board	Replace it and run for the hug	XANDARE