Cce Repair Tips
Search: cce
Results: 4824
Results: 4824
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
CCE |
HPS-2991P
|
TV doesn't turn on | Fuse | Leonardo Miranda | |
CCE |
HPS1402
|
Av block or blocked channel | Password that was in my 1000 | Password 1000 | Hndrsn |
CCE |
21
|
No audio | Capacitor 16v 470uf | Nick | |
CCE |
LN24G
V236BJ1-LE1 |
Turns on without image, with sound and backlight, responding to commands. | Resistance of 0.02 across several capacitors on the v-con board. I had to remove them one by one to check which one was shorted. | In my case the short was only on CD2. replace and jump for joy. | World TV |
CCE |
HPS21AVP
|
The TV turns on and performs all functions, such as changing channels, entering the menu, changing volume, etc... it does everything by itself! | I tested all the micro switches, resistors and nothing worked. | It may be a silly thing, but all it took was redoing the soldering on the ci 101 and the TV returned to normal operation. I hope it helps you friends. | Bruno Cardoso |
CCE |
STYLE D37
|
All white image | Ceramic capacitor cp8 on the v.con board | Take it out and it will work, but if you want to replace it, it's better for the same value but you have to look at the schematic | Eletrônica Júnior |
CCE |
LT29G
|
Reduction of LED current | The correct way is to remove r65 from 1k2 and place a 4k7 resistor on pin 6 of the driver ci. | eletrofepar | |
CCE |
L244
|
Turns back to standby | Capacitor 100uf/50v next regulator 5 volts with cold soldering | Bentim | |
CCE |
HPS 1407
|
Blinks but doesn't turn on | Bc337 in the power supply area! In some cases, just change 1! | ||
CCE |
LN14G
|
Call whenever you want | Faulty smd transistor q19 (good average), close to the display flat cable connector | Replace for an equivalent npn | JL Eletrônica |
CCE |
HSP 1497
|
TV mutes, no audio | I changed the audio output and even tried the equivalent (la42351 and la42352) nothing | With the same original audio output (la42051) I released the 1st leg and the TV worked perfectly! | Eletrônica manauara |
CCE |
1471
|
Blinking led | Adjust screen....it was low | Alextecnico | |
CCE |
HPS 1497
|
TV with vertical sides disappearing image | Capacitor 825 and 831, 47mf/160v and 1000mf/16v, in that order. | Flavio | |
CCE |
TV 2118USP
SL23-1 |
The image took a while to appear when it appeared, it lacked width | Capacitor do +b 100/160 | Replace and always thank God for each service completed | Rogério TV |
CCE |
LT29G
|
Reduce LED voltage | Remove r126 and put r8 in place, and connect r3 and r6 in series | Eletronica Cardoso | |
CCE |
LN24GW
|
Does not tune channels | Defective varicap | BOSCO | |
CCE |
LN24G
|
The backlite doesn't light up | F6 on the 12volt line open | Replace the same | Multimarcas/Acarí |
CCE |
STILE D32
|
Switches to green LED but does not turn on | R97a (10r) open and d25 smd shorted | Eletrônica Cecé. Brumadinho MG | |
CCE |
HPS1497
|
Hitting relay, and with closed vertical | Q802 changed | Replace q802 | MARCONES DE ARARIPINA-PE |
CCE |
TV2118USP/AV. VER 2.2
|
Does not turn on the off LED voltage only on the primary power supply. | The cause of the defect was the ci cq1265rt | It was replaced for a cq765rt as I didn't have the same one and the TV started working again. | José - AssisTec - Manari-PE |