Cce Repair Tips

Search: cce
Results: 4816

Make	Model	Symptom	Problem	Solution	By
CCE	HPS 1471 CHASSI 34BI	Noise in the flipback crickets noise of crickets more or less like that. and it wouldn't turn on, the led would turn off, after 2 times the led would come on again in standby	I found the ic301 stva and q101 bc337/25	Replace them and run for the hug	GENILSON
CCE	CCE HPS 1407S	Standby flashes not turning on	Open flyback	Replacement close and deliver
CCE	D4201 STILE	Sound comes out when turned on, but the lamps only blink when turned on, if it doesn't solve it by changing the capacitors, remove the cn01 plate and place a +/- 82z resistor between the 000 rj5 and the middle pin of z2	Https://youtu.be/ax0vabx4yus	Https://youtu.be/ax0vabx4yus sound's the video of the guy who gave the tip	Rodrigo cofferi
CCE	D3201	The TV would not turn on and the LED remained flashing orange.	Stand by power supply with the main pci connector connected, the voltage fluctuated at 2.4v, if you released the connector it returned to 5 volts. Cause: PFC capacitor exhausted and the IC also shorted.		Alegrete
CCE	21AVP	High leakage in the tube, even after changing all the capacitors	Clean the tube with a cleaning product, especially wsound the pacifier goes	Clean tube	Leonardo
CCE	21AVP	When the deflector coil cables are connected to the board, when turning on the TV, it makes a loud whistle and turns off before the image appears.	Shorted deflector coil	To replace	Leonardo(Deus abençoe a todos ,somos todos filhos de Deus)
CCE	HPS 2081	TV does not turn on with +b with 20 volts 5 volt line giving only 3.5	Q 705 transistor on the stand by just removed it from the location and the TV started working again		Eletrônica São José
CCE	LED24TV	LEDs light up very weakly, image is dark	Cold solder on the capacitor on the side of the diode d11 on the power supply board	Solve capacitor	Eletronicaaeb
CCE	HPS-2185FS	Plug it into the socket and the LED blinks	12v missing - time it turns on time it doesn't turn on	Faulty fr403 and fr402 or cold solder on the pins or broken track	Andre mamilha
CCE	STILE D42	I'm sound	Transistoresq12, q14, q15	Removed and resoldered transistors, resolved the defect. pay attention to keyboard problems with faulty buttons, turn off the keyboard so as not to interfere with the analysis	Claudio Jorge Eckert Junior
CCE	LED24TV	Turns on the red LED, when you press power, the red LED goes off and comes back on, sometimes the green LED starts blinking	5v step down supply on main board	Responsible ci, I replaced the mp1484, with a small replace, since this ci has the gnd pad, I had to scrape the varnish off the board to create an electrical and thermal connection, improving heat dissipation.	Davi.sls
CCE	1491 CM-535A	Vertical closed	Resistor r303 (67k) open, and c301 (100uf/25v) changed.		MARCONES DE ARARIPINA -PE.
CCE	L322 L322	TV doesn't turn on, green LED stuck on stand-by	Dry capacitor at 1.1v supply on main board - ec4 470uf/16v	Replace the same	dsstech
CCE	HPS2097 C	Screen closing on both sides and distorting the color, all you had to do was change the capacitor	C 828 .47mf / 160v		João Batista
CCE	TV2918USP 2918USP	Vertical to dated	What is the solution	What is the problem	Raimundo
CCE	LED24TV	Does not turn on or turn on standby	16v x 100uf electrolytic capacitor EC3 changed on the main board	Replace the same	ELETROSANTOS
CCE	STILE D4201	Irregular sound: low, rumbling, delayed, repeated	Capacitor ec4	Replace 470μF / 16v ec4 electrolytic	ZENER Serviço Técnico
CCE	STILE D4201	Irregular sound: low, rumbling, delayed, repeated	Capacitor ec4	Replace 470μF / 16v ec4 electrolytic
CCE	LT32G GT-1326EX-D292	High voltage on the LED causing it to burn	Replace r9 with a higher value, in my case I put 2 15k res in parallel the voltage dropped from 6.2 to 5.9		eletronica tensao
CCE	HPS-1497P D-1420	Standby lit by pressing power key tv tries to turn on standby flashing and returns to standby	Resistor in the 12v line of the flayblek fr402 and fr403 1.0Ω changed to 27Ω		Eletrônica o Júnior