Toshiba Repair Tips
Search: toshiba
Results: 5617
Results: 5617
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| TOSHIBA |
42XV600
|
Does not care, nor standby | Ci Reset (IC951), is more or less in the middle of the main plate. | Robson | |
| SEMP TOSHIBA |
DL4077L
|
Don't turn on, green LED flashes | Check ICP1 pin 1 tension (TEA1733) If you don't have 24V, replace DP9 even measuring good. | DP9 (diodo fast 1A) | Junior - Tecnoprom |
| SEMP TOSHIBA |
32L2400
|
Does not turn on, does not enter standby so that you can give power, flashes red LED very weak and fast and oscillating, varying, sometimes even enter standby | N802 FR9889, which makes 5 volts for the N805 regulator to produce 3.3volts. | replace n802 | MIGUELTV |
| SEMP TOSHIBA STI |
LE3264B
|
Works But with message in the upper left corner M Mode | Update replace the File Name, MS6328la03_Full_UPGRADE.Bin Leave it like this, through the Power key | Ms6328la03_full_upgrade.bin Update by replace the file name | Rodrigo cofferi |
| SEMP TOSHIBA |
1452(O)AV
U-19 |
League makes a snap after Led Standby lights with the TV turned on after a flashing picture and burnt smell coming from the back cover | Not yet discovered | Has not yet been fixed | K |
| TOSHIBA |
32L23000
|
appears on the screen was detected overload on USB | Ci ic160 | Just break the CI pin 3 trail, this pin is what brings information to the proseser, breaking it the USB continues to work normally | Fabio |
| TOSHIBA |
32L2400
|
After replace the plate, it was upside down and with inverted picture | I tried to put the update to 924693 but it didn't work | I replaced the flash memory from one plate to another tsound worked | david gomes |
| TOSHIBA |
40L2500
|
League appears the logo \\\ "toshiba \\\" and erases the backlight | Cid N701 LED Drive comes into protection | Place a 10kH SMD resistor on top of C718 capacitor and remove R764 to reduce the current in the LED | LOOPTEL |
| SEMP TOSHIBA CRT (TV DE TUBO) |
TV2977(A)SL SL-91
|
Reduced frame in the middle of the tube with a glass and time in Lod green, time-colored time and with retrace and without characters. Note: Sometimes when it turned on the frame I would fill the screen again (normal frame) but only the channel character 2 appeared but did not obey the commands. We swear it is a defective primary power supply. | The cause of the malfunction was incredibly damaged Eprom. replaced the EEPROM memory \\\ "resolved headache \\\" ie problem solved. | Airton Eletrônica | |
| TOSHIBA |
52XV550DA
|
Does not care, nor beat relay, tip on which control works on this TV | The less power supply plate has several bad contacts | SOLUTION RESSOLDAR, IN MY CASE I replaced all covers 10/50, 22/50, 4.7/50, ie I reviewed primary. Remote control that works is the MXTCT6390, too top. | MIGUELTV |
| TOSHIBA |
40L2500
|
Alloy, the logo appears, shuts down. | Check CI N804 3.3V regulator. In Sty is 3.0 volt. When it calls it falls to 2.9V. | replace tsound n804. | arock |
| SEMP TOSHIBA/PHILCO |
32AL800/LE3264/PH32E53
FONTE PE371CO/40-E371C6-PWG1XG |
Green LED connect and sometimes locked in green or VM | Had 12v but did not have the 5v on l 102 | Q100 D13N3 8 Pins | ELETRONICA BRAMBILA |
| TOSHIBA |
TODA LINHA U17
U17 |
Light the LED quickly erases and drops the tensions | C-864 47m x50 Primary power supply | ELTON CASTRO | |
| SOM TOSHIBA |
MS-8012MU
|
No sound | Earphone plug | replace or jamper with welding | Mario Moreci |
| TOSHIBA |
32L2600
MT56E1 |
No picture, or inverted picture when replace the screen. | Place Project ID 184 | Eduardo Costa. B. F Electronics. BH, Minas Gerais | |
| TOSHIBA |
MS7980
|
connect and after already turns off | glue on top of the SMD ceramic capacitor next to the flash memory | Remove the glue, replace the capacitor and leave for the hug | Valdecir Schena |
| SEMP TOSHIBA |
40AL800A
|
Green LED, has 3.3V without 24V, locked in the inoperative green LED | replace TL431 (U402), replace photo coupling (PC2) | Gaeletronica | |
| TOSHIBA |
LC404
|
No picture, with sound. | SMD 125V/7A (F102) Open and CI 4614B (Q310) | replace CI and replace fuse, Note. (Redo the weld of all jumpers OOO resistor of the plate), including those that marked heating under the plate, as they are the causes of CI burn with cold welding increasing the tension over the CI. | Wortec |
| TOSHIBA |
48L2400
|
Only Led Stand by Red Acid | Replacement of CI N801 FR9889 | reginaldo moronte,eletronica junior caldas novas | |
| TOSHIBA |
32L2400
|
Defective or broken display | replace display. | The C320an02S4LV0.1 Display works in place if the picture is inverted use the 924263 serial software. | Capiroto |