Philco Repair Tips
Search: philco
Results: 4838
Results: 4838
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
PHILCO |
PH32N62
|
Voltage of each 6v2 LEDs | R111 , 112 , 114 , 115 do the adjustment , Removi R112 and R115 , Voltage I get 5V8 | Alextecnico | |
PHILCO |
PH32N62
|
BLACKLITE CALLS 1/2 SECONDS AND SHARES | U3 pin 5 has the R110 (100R) , in place put a jamper and worked normal | JAMPER R110 | Alextecnico |
PHILCO |
PTV39F61D
|
It turns on, but does not turn on the backlight, a power supply for the LEDs is 38V in stand-by and by squeezing Power rises to 44 volts, not enough to light the LEDs, in my case even blinking the LEDs. | Near the output connector for the LEDs has the SMD diode position on the DB1 plate, code on the body of the HBR3100 diode in the short circuit, I used the SK320U instead | After exreplace the short diode, the power supply went to 58 volts, which exceeds 54 volts, the 03 6 LED rules in series are 18 3 -volt LEDs. Then I removed R815 from 2R2 and on the side of 2R4 and the power supply dropped to 53.9 volts. | MIGUELTV |
PHILCO |
PTV32G7PR2CSBLH
|
Don't turn on, just stand by lit. Tighten the power and nothing happens | short on plate | CE25 Capacitor, near a sequence of equal capacitors. PLACED ONE OF 22mF IN PLACE | Romildo Behrend |
PHILCO |
PH400N
|
Do not turn on, just the stand by lit red. | Diode d13 na main plate committed | Even measuring good on the multimeter, it was bad | Romildo Behrend |
PHILCO |
PTV32G70RCH
T398B |
Does not turn on lit red led | QE02 and CE68 SMD shortly, is between the micro and the coil Le6 | replace the two | EletroClaudiope |
PHILCO |
PH24R
|
LED lit lit direct and it seems that it is locked | Zener Diode 4148 on the Power Botao plate. | replace and Finish | TecRecall |
PHILCO |
PTV32D10
|
Don't Call - Without Standby | Missing 5V diet. UD5 regulator burned. | replace UD5 for another equal. | EVANDO VIANA |
PHILCO |
PTV32T10EDP
|
Flashes the backlight on the boot (logo) and erases. | Failure (Ripple) in LED feeding, they are not the bars | replace PC208 and PC170, both 47UF/100V Filtering | Baguatech |
PHILCO |
PH48S61DG
|
Don't call is only in the lit lit so standby | Analyzing plate I found IC n806 - SY8087, is receiving 5V trenches not skirt 3.3V to feed regulator N805 1.5V ddr giving 0v, I made the replace n806 tinging tv liga | Solved defect | André |
PHILCO |
PH32F33DG
MS32 |
Logged in the logo, the update does not start | Noise on the 5V line | Remove the 2 capacitors from the audio output. The TV should start normal. If you do not start, now yes update the flash by the flash drive. Update should start, wait ... ready !!! Replace 220mf x 25V capacitors, restore factory mode and receive Pix! Hugs! | edson_tectron |
PHILCO |
PTV40E21DSWN
|
NO CALL, NO LED STAND-BY | Has all tensions, defect in the regulator 3.3V U2P2 | Sylvox | |
PHILCO |
32LM3400
|
The TV turns on the picture for a few minutes and then adds the picture, keeping the sound and the LEDs working. | IC402. When the TV has an picture the 2.5V voltage is present, when it is without picture the voltage is below 1.2V | Replace the IC402 ( | Eletrônica Alves |
PHILCO |
32LM3400
|
The TV turns on the picture for a few minutes and then adds the picture, keeping the sound and the LEDs working. | IC402. When the TV has an picture the 2.5V voltage is present, when it is without picture the voltage is below 1.2V | Replace the IC402 ( | Eletrônica Alves |
SEMP TOSHIBA/PHILCO |
32AL800/LE3264/PH32E53
FONTE PE371CO/40-E371C6-PWG1XG |
Green LED connect and sometimes locked in green or VM | Had 12v but did not have the 5v on l 102 | Q100 D13N3 8 Pins | ELETRONICA BRAMBILA |
PHILCO |
TUBO
|
Track throwing the picture to the singing | C718 from 471 /2kv and 10k r712 | replace both in my case was burned | Rogério TV |
PHILCO |
PTV 32G70RVH
|
STB ONLY | Don't turn on | CE63 in short | Mega eletrônica KB |
PHILCO |
PH40U16DSG
|
When calling, the Philco logo appears and after a few seconds deligs and returns to Tstanby. Sometimes it even opens the normal screen, but when connecting a signal power supply in the inputs, it turns off staying in Standby. | I replaced all 3.3V regulators was beauty | replace 3.3V regulators. | Ferraz |
PHILCO |
PH29T21D
|
With backlight, washed screen | Open Q202 transistor, replace and see if it turned the 12V in VCOM, if you do not check capacitors of the 12V line in VCOM, I found CP5 shortly. Check everyone who is in parallel with him if he is good | ELETRONICA ESTUDIER - OLIBIO | |
PHILCO |
PH40R86DSGW
|
Smoke came out, and picture became dark | Main plate | I replaced, it is working normally | Jonas tadeu martins vilas boas |