☰

Philco Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philco
Results: 4775
Make Model Symptom Problem Solution By
PHILCO PH28C20D LED
099283003 A 		WHEN YOU replace THE LEDS, THE BACK LIGHT FLASHES AND TURN OFF CHECK PIN 7 PROT OF OB3350. R151 330K MEASURING +-50K DUE TO THE GLUE AT THE BOTTOM! ELETRONICA BRAMBILA
PHILCO TV PH21M SS GAME
PH21M SS 		turns on, turns off, standby protection New TV, I took it out of the box, it works for 2 minutes and turns off, I only discovered the defect when I removed the jump from the b+ flaybak, it turned on, then I tested the voltage, it was low capacitors 330N and 15N TVs that use 220N and do not use the 15N test all in the flyback area taylor
PHILCO PTV43E60SN LED
Back light does not come on Cold soldering Ressold IC MP4010 (UB1) and its peripherals Djalma Moreira
PHILCO PH49F30
Stuck on screen, please wait firmware Download the update firmware file. With the pendrive connected, plug the TV into the socket with the power button pressed, keeping it pressed for about 10 seconds, until the LED starts flashing quickly. Davi.sls
PHILCO PCX5600
Does not turn on, low battery It turns on, but as it was out of battery it then turns off... no signal when connecting the charger cable Replacement of the power supply board Photocoupler (U3), and replace of the SR3100 diode (D6). Innovast
PHILCO PH20U21D
Turns on but the picture remains dark LED voltage low at 23.4v UP401 OB3350/So-8 replace the LED IC RV ELETRONICA GYN
PHILCO PH28N91
Sometimes it turns on and works, sometimes it doesn't turn on, it takes a while to turn on, you have to unplug it frequently Replace the 1.8v U3 regulator replace the 1.8v u3 regulator Rodrigo cofferi Rodrigo cofferi
PHILCO PH32E32D
Screen a little dark from bottom to top. replace the LED bar and reducing current. To reduce the LED current, remove R118 and R119 10R and 20R Katutto
PHILCO PTV39N91D
Dark screen replace the LED kit and reducing current. To reduce the LED current, remove PR39 and PR40 1R5 Katutto
PHILCO PC1442
Doesn't turn on buzzing at strong power supply c911 220x250v sold out make an replace and that's it orlando lott
PHILCO PH24D20DM2
Does not turn on, press standby, blink 4 times and return to standby Leaky diode on display in position DP6 Remove or replace, without testing, the leak is minimal and is not noticeable on the multimeter HAHNRAHN
PHILCO PH49F30DSGWA
Backlight does not turn off, even with the TV on standby LED driver IC OB3352CP leaving pin 7 with permanent 8 volts. Dili - RS
PHILCO PH49F30
Backlight does not turn off, even with the TV on standby LED driver IC OB3352CP leaving pin 7 with permanent 8 volts.
PHILCO PH40D10
The LEDs don't light up shorted dp401 diode replace diode Eletronicaaeb
PHILCO PH32S46D
Dead DS2, C113, C114 Replace the Diode and the two capacitors described above. Multimarcas/Acarí
PHILCO PHT3000
Only the green charge LED is on and the display is off. Regulator type T022 -CI 7805 deficient. replace him is running for a hug.. JM
PHILCO PH28N91D
No picture Causing pd10 diode Swap and run for the hug Daniel, eletrônica ideal
PHILCO PH28N92D
No picture, good LEDs Diode pd10_ SS310 shorted Daniel, eletrônica ideal
PHILCO PCX1600
VEX.PH.HOME.048.REV.0 ABRIL/2019 		mute box micro activating the Mute, probable defect in the micro. I can't find the ic, I replaced r106 from 1k to 10k and the box started working again on r106 JOSIVAN
PHILCO PTV42E60DSWN
The LED bars do not light up, sometimes they turn on normally. When cold it was defective, heating the capacitors it would work replace of electrolytic capacitors 100uf x 100v cb2 and cb17 at the output of the led drive power supply Sérgio