Hitachi Repair Tips
Search: hitachi
Results: 1065
Results: 1065
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO HITACHI |
PC 1441
CPH04 |
It doesn't turn on, when you remove it from the socket it makes a high-pitched noise that lasts about 3 seconds | Flyback with escape | Flyback replacement | Luis |
| HITACHI |
32LD9700 42LD9700
|
No sound | Bad soldering on cristal x800 (hdmi board). | ||
| HITACHI |
32LD9700
|
No sound bad conection in pfa1(hdmi board) pin 2 | Just take it out press and put it back. | ||
| HITACHI |
28LD5200
|
No colour colour drops out after the unit has been running for two to three hours. | Resolder capacitor c510 and other components in its vicinity. | ||
| HITACHI |
26LD6600 32LD6600
|
Lines, no pictures back light present | Resoldered ic224 (videoprocesor). | ||
| HITACHI |
26LD6600 32LD6600
|
Lines on the screen | Cable from the main board to screen super glue it. | ||
| HITACHI |
26LD6600 32LD6600
|
Looks like no synchro impulse eeprom fault | Just go in service menu(menu,4,7,2,5) option | Factory reset. | |
| HITACHI |
26LD6200 32LD6200
|
Unit does not work, standby led not lighting | Replace ferrite bead l500 and l501 with a jumper wire. | ||
| HITACHI |
26LD6200 32LD6200
|
No pictures or lost after 10,20sek | Replaced inverter board(p.suplly)17pw11 | 2 (24volts) | |
| HITACHI |
26LD6200
|
Lines on the screen,strange picture | Replaced cable from main board to the screen. | ||
| HITACHI |
22LD4500U
|
No sound | Very low sound on terrestial and no sound on digital or any av inputs | Replace memory ic302 type 24lc16.all customer controls are set to minimum on the new ic. please reset language and all picture controls to normal after replacing the ic. | |
| HITACHI |
22LD4200
|
Stby redlight go green and back to red | Transistor(q104 bc548) and resistor (100om). | ||
| HITACHI |
22LD4200
|
Flashing green line | Green horizontal line flashing across the screen intermittently | Remove resistor r149 on the input signal board and replace it with jumper smd (0 w) | |
| HITACHI |
22LD4200
|
Lines on the picture | Bad connection between ps(pl 108) and video board (pl100) . | ||
| HITACHI |
22LD4200
|
No pictures sound ok | After diferent time check 5v on 17amp07 p/s board if less 3,0 or 1,5 replaced c111(25v1000mkgf) | ||
| HITACHI |
22LD4200
|
Lost picture after different time | Dry joints on video procesor ic100 board (17mb10). | ||
| HITACHI |
15LD2200
|
No pictures | Fuse f1 and c16 or c5(150n) on inverter board. | ||
| HITACHI |
NP91SR
|
It does not work with the first ones turned on after it starts | Change c910 | Pablo | |
| PHILCO - HITACHI |
PSR-60
|
Hoarse sound and distortion | Fusistor r715 (100r) open | The fusistor is located in front of the stk | Marcelo |
| PHILCO HITACHI |
PC2041
|
Closing a little vertical at the top and shaking at the bottom | After changing almost all the electrolics and it didn't solve the problem, I did the capacheck on the c908 | Replace c 908 10 micro for 50v | marciorvgo |