Search: lg
Results: 4876
Make Model Symptom Problem Solution By
LG 32LE7500
The TV only lights up the LG logo on the front of the device and the buttons with no sound or image. C201 and c202 burst on the power supply board, both 150uf/6.3v. Replace for 220μF/16v. Marcio Eletrônica
LG 20LS1R
Dead TV when I pressed the power button, the green LED turned on and then the red LED flashed. C202, c203, c204, c205 and c206 brazed and cold welded on t101. Replace and run for the hug. Marcio Eletrônica
LG 21FU1RL
CW81A
TV turns on with power supply B+ low 83 volts black bands a little distorted on the sides of the TV TV Q801 leaking Replace q801 ROSIELDO CARVALHO
LG 50PB650B
Doesn't turn on - doesn't have 5v Replace ic301 strw6051s e zd 303 10v Replace molina
LG 32LN536B
LA3AA
No image. audio only. Back light bars with damaged LEDs. Replacing the LEDs. detail: I lowered the circuit current. I removed the power supply resistors r827 (3r9), r826 (4r3) and replaced r823 (from 3r9 to 4r3) and r825 (from 3r9 to 12r). they were 71.4v, 394ma to 65v, 243ma. I lowered the current a lot because it was feedback. Eletrônica R-Tec
LG RAD 136
No sound and cd doesn't work Shorted 5v line, causing no sound and killing the power supply to the ic301 Replace c312 (electrolytic short, close to ic 301) Fofao eletrônica estância
LG 32LD350
Pci killing power supply voltages PCI capacitor c459 shorted I removed it and the TV is ok Jetro vieira
LG W1942P
Turns on, image appears and turns off (remains on without the screen lighting up) Burned-out fluorescent lamps side a or b use two lamps on each side. Just by changing it to another one, it burns out due to the number of hours of use. Maike Sorriso-MT
LG 42PQ30TD EAX56395204(0)
It calls whenever it wants and sometimes it only calls after several attempts Two capacitors on the main PCI c866 and c863 Exchanging them Airton Filgueira
LG L1750S
Backlight blinks Low capacitance c101 68uf 400v Replace rikadapper
LG MCT705
Turns on with cricket in the chopper (70v) without load (removed the output) the +b 70 slowly rises to around 60 Open 10k r916 EletroFenix
LG 42LB9RT
When plugging the TV into the socket, a popping sound was heard and the stand-by light turned red, but the screen turned on and the sound didn't work. Found electrolytic capacitors c202, c206 and c217 (all 2200uf/10v) swollen. the ci u101 (it was blown, without the top "cap"), the mosfet q103 shorted, the zener zd100 burned and the smd resistors r114 (100r), r115 (10r) and r118 (560r) and common resistor r120 (0.33 r/2w) burned. After replacing all components, the TV started working again.
LG 32LV536B
No image. audio only. Defective LED bars. Replacing the LEDs. detail: I lowered the circuit current as it was the second repair on the same device. On another occasion I noticed the same defect. I removed the power supply resistors r829 (3r9), r828 (4r3) and replaced r825 (from 3r9 to 4r3) and r823 (from 3r9 to 5r6). the measurements went from 40v and 139ma to 37.3.1v and 97ma. Eletrônica R-Tec
LG 43LJ5550
LED blinks and doesn't turn on Shorted smd capacitor underneath wifi board Hndrsn
LG 47LW6500
Turns on and no picture and no sound Redid processor reflow and capacitor c5412 in short dropping 1.2v_frc CARLOS STYLO
LG 50PJ350
It didn't work, check if tsound was a short and I only found it on the 5 volt line. Main board, c502 underneath and next to the p500 connector fabiusmax
LG 32LH570B
Turns on only turns on the backlight Ic 500 (mp3378e) burned on the main board. Note; tsound is no 12v that powers the vcon. After changing the TV ok. George Pontes
LG 32C460C
Turn on the lights and turn them off leaving only sound Weak light bulbs Put a 10k resistor on pin 13 of the bd9270f to ground and replace 39k r301 with a 100k barbadinha
LG RP14CB25A
No image appears, turning on and with normal sound, but no image. C814 Capacitor replace, it was bloated. Elton
LG DH4220S
Without video on HDMI, only black and white video output (AV) worked If you can't. reset the device. setup>> video>> 16:9 on the controller press 1397139 enter on the screen that appears press enter again. Turn the device off and on again using the remote control, select the device language and have fun