Lg Repair Tips

Search: lg
Results: 4876

Make	Model	Symptom	Problem	Solution	By
LG	50PN4500	TV does not recognize HDMI or RCA input	Lack of power at the AD5 output of the processor	Plate replacement	Core Assistencia
LG	20CB20	Lines at the top with a little white stripe	R 301 of 470r giving 560r just change this resistor and bam..		Diego lima. nova TIMBOTEUA para
LG	29CC9RL	Alloy with closed vertical, normal currents	Deflector with broken wires	Changing the deflector	Eletrônica
LG	39LB5600	Very white screen with very faint sound and image.	Changed, went back to normal.		gesuino
LG	21FU4RL	No image in av, just squeaking sound	Yashkhah1=Lahahaha0	Replaced and solved the problem	Antonio Carlos (Eletrônica Renascer)Boa Vista do Gurupi-MA
LG	50PJ350	Blurry image and black spots	R426 keeps burning, due to cold solder on the fuse on the zsus board. resolder all cold welds on ysus and zsus	Resolder ysus and zsus and replace r426	MAIATECH
LG	MCD606	Tsound was no lighting on the display	Open power supply diode 931.	D931 diode replacement	eletronica d.olho ,,paulo
LG	RP-14CB25ABRS	Vertical fully closed, only line in the middle of the screen.	Change the resistor (r313) and the problem will be solved.		Wellington tec
LG	29 MC022A	I'm sound	Dried solder	Resolder the two cis, the sound output and the memory	bse eletros
LG	RP-20CC97 MC-059A	Blinking led	Dz851 6v2		carlinhos100
LG	CM4330 CM	It turned on, read the pen drive and turned off	After a lot of testing I discovered the transistor q-953 in the test it looked good but the original was open and an ST25c I replaced it with a tip41c	Replace it for another equal one or a tip41c solves it	ELETRÔNICA CAVALCANTE MARTINÓPOLE-CE
LG	32LN536B	Black screen with backlight	Llineartj1118 2.5 volt regulator. ic402 next to nand memory	3.3 volts at the input and if the output does not measure 2.5, you can replace it and it will solve	Williston
LG	42PT250	Stopped, stdby is on, it looks like it's going to turn on but goes back to standby	Q11 and q12 shorted and sometimes q15 and q16 too, after changing them check c721 may be burnt, you can't measure it, just check it if it's perfect, I advise you to remove it and leave it without it		VICTORINO
LG	42LM3400	Slightly negative colors, with three curtains over the image	Leaky capacitor in the t-com and display circuit;	In my case, I replaced the c-124 capacitor on the display ruler	jairoeletrotecnico
LG	32LK330 EAX61124203/2	TV turns on the LED and it blinks, no image, no sound, LCD lamps don't light up	In my case, two MOSFETs K3868 Q707 and Q709 are shorted, opening the fuse F501 15A/250V in the inverter area on the power supply board	Replace the fuse and the two original k3868 mosfet, you have to put the original k3868 mosfet	Ricardo Montes
LG	CM 4350	Dead power supply	Burnt mosfet spa08n80c3	Replace for the same one or the p6nk90zfp... more zd 912, zd902, c914,c905	Junior da Eletrônica Alves V. Grande -MA.
LG	CM 4350	Dead power supply	Burnt mosfet spa08n80c3	Replace for the same one or the p6nk90zfp	Junior da Eletrônica Alves V. Grande -MA.
TV LG	29CC9RL	Vertical - dark screen on the top, open only about 10 cm on the bottom. (below)	Resistor r567 (4k7) open or altered. (also check r566 same value 4k7)	Replace resistor	Severino Silva
LG	42LC4R	TV doesn't turn on	TV without 5v power supply - open 2r2 metal film resistor (r508) at the power supply. It is located between the 2 large capacitors of the primary power supply. If after changing the resistor the power supply is "buzzing", that is, making a noise in the 5v power supply transformer, replace the 3v6 zener (zd501) which becomes shorted. I hope I helped.	It's also good to replace the c210 (1500mf/35v) that replaces.	Gerson Digitecnica
LG	21FU1RL	Doesn't start. LED flashes and comes on again. +b normal on standby.	Bad 2200uf x 25v capacitor c311. In my case it was measuring as good. change without measuring.		Carlão