Philips Repair Tips
Search: philips
Results: 14209
Results: 14209
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
L6.2AA
|
Repeated failure of loptr | Caused by 5420 coil in loptr base o/c pt no 4822 157 50965 | ||
| PHILIPS |
L6.2AA
|
Line o/p tr repeated failure | L5420 int o/c | ||
| PHILIPS |
L6.2AA
|
Int dead | Transistor 7507 in psu near chopper tfmr bc337-40 | ||
| PHILIPS |
L6.2AA
|
High ht | R3510 33k hi res | ||
| PHILIPS |
L6.2AA
|
Dead - blown psu & s/c lop tr | Caused by 5420 coil in loptr base o/c pt no 4822 157 50965 | ||
| PHILIPS |
L6.2/6.3
|
Goes dead with no led lit aft few mins | Tr 7505 bc337-40 replaced | ||
| PHILIPS |
L6.2 L6.3
|
Chan lock up etc | Replace tr7505 bc337-40 | ||
| PHILIPS |
L6.2 AA
|
Dead with whine from psu | C2012 2n2 2kv - cracked | ||
| PHILIPS |
L6.2 286NS
|
Narrow, snowy raster with bright strip 2 inches wide down middle, no sound or r/c. | Replace transistor 7505 near chopper transformer bc337-40 which read high. | ||
| PHILIPS |
L6.2 25PT4494
|
Shuts down aft a min with cogging - ok at restart | Tr515 and choke 5428 | ||
| PHILIPS |
25PT4103/05
L6.2 |
Cool fades out after 10 mins then starts to trip | Tda8361 ic7100 pt no 4822 209 13047 | ||
| PHILIPS |
25PT4103
L6.2 |
Pulsing psu & eht | R3425 12r in line dr o/c | ||
| PHILIPS |
25PT4103
L6.2 |
Line & pulling moving up or down pic | 7501 bf487 in power supply. | ||
| PHILIPS |
25PT4103
L6.2 |
Int dead apart from buzz or lines/disturbance | Transistor 7501 bf487 | ||
| PHILIPS |
25PT4103
L6.2 |
Dead with smoke | C2912 2n2 2kv split but no pic with buzzing when replaced - works on 200v ac - check r3514/5 1r ½w current sensing res in psu | ||
| PHILIPS |
L6.2 21PT1653
|
Dead, chopper tr s/c | R3524 22r gone high | ||
| PHILIPS |
L6.2
|
Noise on one channel or stereo indication on mono transmission | Replace ic7353 msp3400c (482220913099) | ||
| PHILIPS |
L6.2
|
Width/ e/w dist | C2915 390nf o/c | ||
| PHILIPS |
L6.2
|
Width control inop | Tr7908 stp4na40f1 s/c between gate & power supply | ||
| PHILIPS |
L6.2
|
The set does not work anymore after switching it into the standby mode | Replace the line output transistor 7906. also replace the line output driver transistor 7421 by type bc368-25 (use only a philips version) the service code of bc368-25 is 933869720112. remarks : the cause is that the line output transistor 7906 |