Search: philips
Results: 14247
Make Model Symptom Problem Solution By
PHILIPS FL1.2S
Wrong synchronization, unstable colors D6417 on the lsp dependent on temperature, check/replace (4822 130 81223)
PHILIPS FL1.2S
Wrong service batch of st24c08cb1 memory ic's Wrong service batch of st24c08cb1 memory ic's 4822 209 32283 ------------------------------------------------------------ temporarily a wrong batch of earom's has been delivered, causing the fault "nvm memory not write protected" after replacing the earom
PHILIPS FL1.2S
Unstable picture, horizontal jitter. Check/replace r3405 on the lsp. (4822 051 10303 for 50 hz sets; 4822 051 10333 for 100 hz sets).
PHILIPS FL1.2S
Tuning does not function Resistor r3240 on lsp in v-tuning wire broken.
PHILIPS FL1.2S
Totally inoperative. Transistors 7250 (bux85f; 4822 130 62509) and 7251 (bc848; 4822 130 61207) in microsops defective. or d6251 (llz-c5v6; 4822 130 80954) and r1250 (=r3230; 1Ω; 4822 052 10108) defective. or t7270 (bd825; 4822 130 41746) or t7201 (bc857c; 5322 130 427
PHILIPS FL1.2S
Total inoperative, leds blinking, error 99 Check and replace if necessary c2504 and/or 2505 (2kv hrr) on the large signal panel. replace by a 3kv15 hr-r capacitor if possible: 820pf 4822 126 13152 1nf 4822 126 13153 1,2nf 4822 126 13154 1,5nf 4822 126 13155 1,8nf 4822 126 13156 2,
PHILIPS FL1.2S
Ticking noise and line in picture Transistor 7381 (bc848c; 5322 130 42136) defective when hot.
PHILIPS FL1.2S
Synchronization, picture disappears D6703 and t7704 defective on picture tube panel.
PHILIPS FL1.2S
Switch-off spot visible longer than 5 seconds. 1) change item c2518 on the lsp into 10uf 250v (4822 124 23494). 2) for 29" and 33". as service solution the eht cable can be replaced by 4822 218 21041. this eht cable with bleeder provides a faster discharge time. remarks : 1) so
PHILIPS FL1.2S
Spook in picture Use special antenna cables. codenumbers: 4822 321 61224 pal 1 meter 4822 321 61225 pal 2 meter 4822 321 61226 secam 1 meter 4822 321 61227 secam 2 meter
PHILIPS FL1.2S
Spare parts remote control rc64xx Spare parts remote control rc64xx --------------------------------- codenumbers for part of the rc64xx remote control: flap right 4822 432 92716 flap left 4822 432 92715 battery lid (cover) 4822 432 92714
PHILIPS FL1.2S
Pip picture not in order. Check r3345 (4822 111 41424) in pip unit, check ic7755 (4822 209 63423).
PHILIPS FL1.2S
Picture twists from top Voltage of pin 8-ic7450 (tda3654q) on the lsp has raised to ca. 20 v. check diode 6451 (bzx79/c5v6; 4822 130 80954).
PHILIPS FL1.2S
Picture twists from top Voltage of pin 8-ic7450 (tda3654q) on the lsp has raised to ca. 20 v. check diode 6451 (bzx79/c3v6; 5322 130 34834 or bzx79/c10; 4822 130 61219)
PHILIPS FL1.2S
Picture often dark Check ic7201 in high end-box (saa9042p/a; 4822 209 31851)
PHILIPS FL1.2S
Picture disappears shortly after 30" or control does not function. When hot, 13,5 mhz clock stops working; change the value of r3123 to 1k2.
PHILIPS FL1.2S
Picture disappears (fly back lines), on stereo and dual leds blink Check ic7430 (tda4680). when tda4680 is too hot there is no picture (4822 209 31592).
PHILIPS FL1.2S
Picture dimming with subtittle. Change the following items on the picture tube panel: - item c2708 changed into 270pf (4822 122 32142) - item r3707 changed into 33Ω (4822 051 10339) remarks : introduced in production in week 9326.
PHILIPS FL1.2S
Overview of sops repair kits Overview of sops repair kits ---------------------------- fl1.0 ag00 upto ag03 4822 310 20492 fl1.0 ag04 and higher 4822 310 31921 fl1.0s 4822 310 31924 fl1.1 25" and 28" 4822 310 31919 fl1.1 33" 4822 310 31932 fl1.1s
PHILIPS FL1.2S
No sound, "on, standby, i" leds blinking 10mhz crystal 1602 on the ssp defective, 4822 242 80276