Philips Repair Tips

Search: philips
Results: 14243

Make	Model	Symptom	Problem
PHILIPS	14PT100G/78R	Just sprinkles	When trying to change channels, only the channel indication (OSD) appeared and no image or sound. When trying to auto tune, the entire procedure was carried out without any channel being detected or memorized. checking the tuner and its peripherals, I found r3009 (180Ω) open. His replacement brought normality to TV.
PHILIPS	GR6-LS -26 E 29 POLEGADAS	Loop on color channels (29)	Regulator 7905
PHILIPS	GR6-LS -26 E 29 POLEGADAS	Doesn't work	D-6505 (leak or short)
PHILIPS	GR6-LS -26 E 29 POLEGADAS	Doesn't work	Ts 7502 (see broken terminal)
PHILIPS	GR6-LS -26 E 29 POLEGADAS	Doesn't work	Pin 8 trafo soup (track that/)
PHILIPS	GR6/AL/GR6LS	Vertical height and linearity	Geometry adjustment
PHILIPS	GR6/AL/GR6LS	Drizzle in the canals	Adjust agc (pas/. c m. service)
PHILIPS	GR6/AL/GR6LS	Loop on channels	Aft adjustment (step d m.service)
PHILIPS	GR6/AL/GR6LS	There is only image on the av	Ts 7280 (with leakage)
PHILIPS	GR6/AL/GR6LS	When increasing the volume it drops	Ic 7345 (micro)
PHILIPS	GR6/AL/GR6LS	LED doesn't work	Str 7400 (power supply sops)
PHILIPS	GR6/AL/GR6LS	Does not work LED flashes 6 times	Defective fly back
PHILIPS	GR6/AL/GR6LS	Does not work LED blinks 2 times	R3537 (2k7) open
PHILIPS	GR6/AL/GR6LS	Does not work LED blinks 2 times	Ts 7500 (ts driver horizontal)
PHILIPS	GR6/AL/GR6LS	No image with/sound	EEPROM data loss. exchange it
PHILIPS	GR6/AL/GR6LS	No image with/sound	Ic 7855 (vertical)
PHILIPS	GR6/AL/GR6LS	No image with/sound	C-2573 (contrast)
PHILIPS	GR6/AL/GR6LS	No image with/sound	C-2226 (100k)
PHILIPS	TV PROCESSADA	Gl,cn models	First step, if the device is turned off, you must turn off the resistance that controls the power supply in the case and a resistance of 4.7k (r-3924) (processor reset resistance). If the device does not turn on, the defect is in the power supply. and if you turn it on, the defect is in the processor. defect in the power supply: it could be an open electrolytic capacitor, diode transistor or the protection SCR. processor: it could be the processor itself, but first you must check the 5 volt power supply, the e-eprom (memory integrated circuit) or the sand-castle pulse or the vertical integrated circuit as there is an operational amplifier working inside it with the sand-castle wrist. If you change the e-eprom you must program the new one as it is not programmed. see item adjusting an eprom on a phillps television when changing the e-eprom nothing will appear on the device screen it will only light up the tube filament to see anything you must increase the voltage on the tube screen grid a little.
PHILIPS	CN	Every time you turn on the TV or change channels, the sound takes about 5 to 8 seconds to appear.	This involves changing the electrolytic capacitor in the remote control receiver box, opening the shield and putting it back.