Samsung Repair Tips
Search: samsung
Results: 3878
Results: 3878
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SAMSUNG |
CHASSIS KS1A
|
Start sem ht | R303 replacement | ||
| SAMSUNG |
CHASSIS KS1A
|
No video with feedback lines | R423 replacement | ||
| SAMSUNG |
CB20S10BZ
|
Without image, with osd | R420 120k | ||
| SAMSUNG |
CB-3335Z CHASSIS P69SA
|
Horizontal stripes across the screen. | Leaks on r305 and r308. | ||
| SAMSUNG |
CB5020T CHASSIS SCT11D
|
White screen with vertical colored spots. | 220k r508 replacement on crt board | ||
| SAMSUNG |
CX-5344N, CH S-51
|
It takes a long time for the image to appear after turning on the device | Ic tda6108jf, on the kinescope board, with anomalies | ||
| SAMSUNG |
CHASSIS P69SA
|
Does not come out of standby. | Eeprom 24c02 | ||
| SAMSUNG |
CB 5035Z CHASSIS P69
|
Gives sound. does not give an image. | The cathodes had little emission and the rgb was blocked. I got the kinescope back and everything was normal. | ||
| SAMSUNG |
CB20B30BT -CHASSIS S15A
|
The LED turns on and off. the 8 v voltage on pin 8 of the ic802 does not appear. | Optocoupler pc801 | ||
| SAMSUNG |
CB-5051X CH P68SC-N
|
It turns off with the remote control and turns on again but with an image sometimes with rain and no sound. | Replace q802 (2sc2331) which was leaking | ||
| SAMSUNG |
CB-3351X
|
Image pulled 2 or 3 cm to the left, leaving a black bar on the right | C404 2n7 next to ic101 | ||
| SAMSUNG |
CX-683 - CHASSIS S51
|
Sometimes it doesn't start the horizontal | C407 - 1nf/2kv | ||
| SAMSUNG |
SP47W3HF -RETROPROJECTOR
|
Deconverged image | Icz104 (stk392-040) no convergence module | ||
| SAMSUNG |
CHASSIS S51A
|
Image with poor quality, the voltage of the g2 has a maximum value of 300v | Happened to crt thomson. the solution starts by replacing the transformer lines, 300v is very little, it should have a maximum value of 650v | ||
| SAMSUNG |
CB-5073Z -CHASSIS SCT11B
|
White screen with thick horizontal white lines about 2cm apart that persist even when lowering the g2 | R508 (220k) no módulo do crt | ||
| SAMSUNG |
CX-6230ZN
|
The power supply does not start | Substituir c808-100uf/25v | ||
| SAMSUNG |
CX-6844N - CHASSIS S51A
|
Tsound is no sound, but tsound is background noise like rain. | Go to service mode, menu option byte and select the pal b/g system indicated by the initials cb. After making this selection, exit the service menu, restart the TV, return to service mode and reset. et voilá, the sound appears after 5 seconds. | ||
| SAMSUNG |
CB-504Z
|
The power relay turns on, but does not start, ypc is not powered | Trs: q403 (2sc2229) open, does not feed ypc. and the horizontal drive | ||
| SAMSUNG |
CB-5073Z
|
The LED is always yellow and the TV doesn't turn on despite having the fa ok. | R914 47Ω 1/8w aberta. liga ao pino 16 do up "hold in" | ||
| SAMSUNG |
CL21M21MQ
|
LED blinking and won't turn on | Diode 1n4148 in position j823 open. |