Samsung Repair Tips

Search: samsung
Results: 3845

Make	Model	Symptom	Problem	Solution	By
SAMSUNG	UN46F5200	Sound failing, especially when the volume is medium to high.	Suspension of both speakers destroyed.	Just replacing the entire speaker or just the speaker.	2000
SAMSUNG	UN46F5200	Backlight flashing intermittently	Bad contact on the vr9530 potentiometer on the power supply board (it is on the part of the inverter close to the connector that goes to the backlight)	The potentiometer travels just under one turn, so first of all, mark the original position with a permanent marker, use contact cleaner spray and turn the potentiometer to remove the oxidation. return to the original position.	2000
SAMSUNG	UN32C4000 PD32AF0E_ZSM BN4400349A	Stop, dead power supply	Ci um801s (q0765r) blown, fuse fb801s open, capacitor cb806 and cb808 bloated, transistor qm801 shorted, zener diode zdm801 shorted and db804 shorted.	In my case, it was just a matter of changing these components and running for the hug! transistor qm801 was blown and I couldn't see its reference, but as it pollarizes the qm801, I took an A4 from scrap and the zener diode is a 12v zb smd I took from scrap too!	Rafael Sena
SAMSUNG	UN40D5500	Does not recognize a/v only component	I did a reset and it didn't work, so I connected the white and black wires to the blue RCA of the input connector.
SAMSUNG	PL43F4900	Does not turn on, standby LED does not light up, voltage of 5 volts fluctuates	Cold soldering on icb801s	Resolder all terminals	Wagner Júnior
SAMSUNG	UN55JU6500G	Turns on the LEDs but no image	Plate t with	Remove and clean well with isopropyl alcohol and put new thermal paste that will solve the problem in my case, good luck	eletronica publison natal rgn
SAMSUNG	CL21C650ML	It doesn't turn on, it oscillates and dies, oscillates and dies,	Replace ci verrt		dj pituka
SAMSUNG	HT-Z220 XAZ	After 5 mits. On, it indicates fan_chk on the display, triggering protection, and turns off the device.	Smd resistor nr 19 changed, replace with another 10r	Replacing the smd nr19 cooler protection circuit.	ANANIAS- VP- ELETRÔNICAA
SAMSUNG	CL21A551	Mirroring of the image and retrace lines on top.	Defective vertical ci.	Replace the ci, (tec edfersom, varjota-ce)	Edfersom
SAMSUNG	CL21C650ML	No image in av, in rf, perfect image	Change dz702, dz705, dz7101, dz710, both 9v1.		dj pituka
SAMSUNG	LN32B450	Lamps don't light	Pfc only stays at 170volts, pin +b of pfc ci with zero volts, removed ci voltage rose to 14volts, ci conclusion short	Replaced ci, pfc went up to 385 volts, perfect picture.	Maurilio
SAMSUNG	CL-21Z50MQ KSCA	Band on the left side of the screen (loss of horizontal synchronization).	Leaky zener diode 403.	Just replace it and that's it, problem solved.	Francisco Oliveira
SAMSUNG	T22A300	Standby LED flashing, +5v and +13v pulsing	Ds812 diode in open power supply	Replace with IN4007 Type F (High Frequency)	Werner Schellmann
SAMSUNG	HT-C550	Arming protection when switching on	Capacitor c5n2 shorted on the power supply board	Replace capacitor c5n2 (470/16).	jean alves
SAMSUNG	50PB560B	Has sound, no image	All normal vs and va voltages, but without 18v and 5v on z-sus	Z-sus board replacement	Arnoltec
SAMSUNG	UN55F8000	Restarting with smart logo	Ci slc1013m with defect on the power supply board	Replace of the same	Arnoltec
SAMSUNG	UN40H4200AG	Does not turn on, stand by LED is off	Ic 207 faulty dc dc converter	Replace	Maurilio
SAMSUNG	MX-730	Dead	Fuse 6.3a 250v		NEW PEK ELETRÔNICA
SAMSUNG	UN32J4290	Tv restarting	Look first at sensor control. remote control, if it is blinking as if it was receiving a signal from the remote control, just change this sensor and the problem will be solved.		Alberi F S
SAMSUNG	UN40FH5303	The LED keeps flashing and doesn't turn on	Change the power supply cm872 and cm873		Eletronicaaeb