Samsung Repair Tips

Search: samsung
Results: 3878

Make	Model	Symptom	Problem	Solution	By
SAMSUNG	UN32F4200AG	Standby blinks and TV does not turn on, LED power supply oscillates	It appears to be a problem with the power supply board, but the problem is with the LED, the standby blinking is normal, the problem is with the LED (in this case)	Replacing the defective LED or complete bus	Claudio Eckert
SAMSUNG	PL51F4000	Sometimes it turns on, sometimes it gives no signal, sometimes it turns off out of nowsound and stays dead for a while	3v3 from eeprom failing	3v3 regulator failing, ic806, I adapted another larger one, from the 1117 smd series with wires	davi.sls
SAMSUNG	CL_2958ZMG	Burned horizontal exit	Very high power supply voltage		Francisco Lira Araujo
SAMSUNG	42L2400	Turns on and off after the Toshiba logo appears	Disarming power supply voltages	Replace resistor r766 with 10k as friends have already commented, it worked the first time. thank you all	CDS_DIAS
SAMSUNG	LN40C530F1M	Led on and does not obey commands either on the keyboard or on the remote	Ic203 z1031.	Replace ic 203 z1031. on the signal board.	<small>wellingtoneletronicasilva @bol.com.br</small>
SAMSUNG	UN39FH5205	Dark screen without backlight	Burned out leds	Replace all the rulers or burned and unburned LEDs due to wear. replace the value of r 9110 d3 1r5 to 3r7 to reduce the current and voltage on the LEDs in order to extend the useful life of the LEDs	marco.32
SAMSUNG	UN32D5000PG	TV working, but with weak backlight, very dark image.	Defective power supply board.	Replace the sign and run for the hug.	Marcio Eletrônica
SAMSUNG	UN40H5303AG	Audio only	I noticed the supply voltage indication was high	Replace altered LEDs and double the value of the ovp resistor	Warley cesar
SAMSUNG	UN55MU6100G	No image	Display defect	Changing the display	Tuta
SAMSUNG	CL-21Z58MQ	No audio	Dz871 -8v2 short and l201 -10uh open	Replace defective components	Cláudio Técnico Surubim PE
SAMSUNG	PL43D491A4GXZW	The TV turned on but had a bad image.	Defective power supply, I thought it was the buffer but the power supply had a power supply change.	Defective power supply, the correct power supply was not supplied. I replaced the font and the image returned to normal.	ELETROIN BRASÍLIA
SAMSUNG	PN60H500	Add image and continue with audio	General resoldering at the power supply, mainly on the ds824c and ds825c diodes		reginaldo moronte,eletronica junior caldas novas
SAMSUNG	PL42B450	S.by lit directly. power supply only arms if forced p.on. seems to be the main one, but it was the sensor board	Cap smd		Alexandre Batista
SAMSUNG	PL42B450	Negative and grainy image, (whitened) twisting or squeezing the y-driver sometimes becomes normal (m.contact)	Tr, mosfet 2n60 intermittent defect, tsound was no point in resoldering.	Replace mosfet 5501	Alexandre Batista
SAMSUNG	LN37D550K7	Does not turn on. stand-by LED is blinking.	Shorted capacitor smd c1011 on the board close to the Audio out socket.		jositecalves
SAMSUNG	UN40J5200AG	Completely stopped	Dm8610 diode shorted, just change it and it will be fine		sergio marques
SAMSUNG	LT9B300	Dead secondary power supply.	D861 shorted! (generates the initial a5v)	Replace for the same one.	EvandoViana
SAMSUNG	CL-29K40MQ	Does not turn on with high power supply 160 with LED off	R.924 close to memory	Replace r924	Rosivaldo
SAMSUNG	LN32B350F1	TV turning on with no picture	Pfc voltage with 170v	I replaced the fan7530, but I used another compatible IC, the sem3040, so the voltage rose to 300v, but it didn't turn on the backlight, so looking at my colleagues' tips, I found a solution by placing a 4k7 resistor on pin 16 of the sem2006 to the on/off pin reverse the board connector, then the TV turned on the backlight and started working normally again, thanks for the tip from my friends!	Michael
SAMSUNG	UN40J5500AG	With sound and image fading	Change the qm886 aberyp transistor in the power supply		ELETRÔNICA MUNIZ BAHIA