Sharp Repair Tips
Search: sharp
Results: 1789
Results: 1789
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SHARP |
DV6632H
|
Dead - chopper tr 2sd1546 s/c | Check dry joints in psu esp on q603 & r710 100k 2w hi res & ic700 mc446022p2 shorted | ||
| SHARP |
DV6632
|
Int blowing line o/p transistor or int line collapse | Check for dry joints on scan pcb on crt | ||
| SHARP |
DV6632
|
Dead - when sw on from st/by led goes green for 5 secs then reverts to red | Processor ic800 mc44002 | ||
| SHARP |
DV6603
|
Loss of col phase , white pic , or no raster | Ic1411 nvm sharp ch-ix1409cjh7 | ||
| SHARP |
DV6603
|
Clicking noise from speakers | Replace ic0302 | ||
| SHARP |
DV5940H
|
No pic | Replace frame chip, r645 1Ω 1 watt fusible and c506 100µ 50v | ||
| SHARP |
DV5940
|
Height lacking & 3 fb lines at top | C501, c506, c512 all 100µ | ||
| SHARP |
DV5940
|
Dead - bu508a loptr s/c every few days | Dry joints scan coil plug on main pcb | ||
| SHARP |
DV5937H
|
Hum on sound & no pic via scart | R615 0r82 1w pin 5 loptx derived 12v supply hi res | ||
| SHARP |
DV5937H
|
Field collapse | 42v pin 8 ic500 ok but no 16v pin 4; check fusible res r615 & d601 - pt no rh-dx0127cezz | ||
| SHARP |
DV5937
|
Field collapse & lack of width | R615 0r82 1w o/c, d601 dx0127 s/c | ||
| SHARP |
DV5937
|
Dead - lop tr 2sd1546 faulty | Dry joints on scan coils | ||
| SHARP |
DV5935H BCTV-A
|
St/by only | Loptr q600 2sd1546, c619 560nf 250v & check r619/632 39r safety res | ||
| SHARP |
DV5935H BCTV-A
|
Dead - q600 2sd1546 loptr s/c | R619 39r ½w & r632 39r ½w fusible burnt; c607 0µ56 line scan coupling cap o/c | ||
| SHARP |
DV5935H BCTV-A
|
Dead - chopper tr q705 2sd1546 & ic700 mc44602 chopper control chip both s/c | C712 100µ low cap, d708 & its feed res burnt up; now no sec supply to 12v rect as t700 chopper trfmr damaged | ||
| SHARP |
DV5935H
|
Changes to field cct . | C516 has been removed , l500 has been changed to 180r 0.5w resistor pt no -xz0227bmzz | ||
| SHARP |
DV5935
|
Low width, poor e/w, field cramp | C607 & l604 | ||
| SHARP |
DV5935
|
Dead - r632 & 619 39r burnt | Replace also c619 0µ56 250v & resolder l603 & check 2sd1546 loptr & scan coils conns | ||
| SHARP |
DV5932H DV5935
|
Stuck in standby. | Cracked print around lopt t600 | ||
| SHARP |
DV5932H BCTV-A
|
E-w dist | L604 e/w coil burnt & c607 0µ56 250v |