Repair Tips
Search:
Results: 87709
Results: 87709
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| HOTSOUND |
MODULO LVS
1300/1600 |
Todos leds acesos (on/signal/low limit/high limit) | Signal input board without (-15v) very low (-1.5v), has (+15v) on the CIS NE5532/TL072 (similar to NE5532: RC4560) | Current leakage under 10μF smd capacitor (soldering resin) clean with alcohol | R |
| SEMP TOSHIBA |
LE 4057I (C)
9235 |
Connected but not browsing | I don't know | Wilmar Farias | |
| LG |
32LV3500
|
Takes time to call | C105 smd no pino 7 do ic101 power supply | Pardal-x | |
| LG |
LG32LE5300
|
No sound or no sound | In my case it was an open track near the sound output. | Luciano Fontes | |
| PHILCO |
PH32C10DG
|
Update | Can't find any update on the philco website | Use an update from another model, the ph32c10dsgw works in its place, the boards are the same, drivers.philco.com.br/tv/hkc/ph32c10dsgw | Capiroto |
| PHILIPS |
43PFG5100
|
Tsound is no audio | Change q706 | Agnaldo | |
| PHILCO |
PTV43E3AA
|
Entered without image, only LEDs on | Defect in the tcon, resoldering in the integrated circuit, and the voltage pwm | Just resolder and run for hug, cold solder, I soldered them all with a thin tip. it was fillet | Elison48 |
| SAMSUNG |
LN32C450
|
Only turn on stand by | Shorted capacitor cp814 220nf by 2k | HP ELETRONICA | |
| SAMSUNG |
LN19R81
|
Inverter protection | Wear of the LCD lamps. | Transistor q1 is responsible for the protection circuit when the lack of phase in reverse (shorted lamp or inoperative output) or one of the phases is uneven (lamp wear) and a potential direction is generated and q1 is activated, well I put a resistor 10k from the collector of this transistor to ground and the protection circuit stopped activating, when the collector raised the voltage above 1.0vdc the protection was activated, with this resistor the collector remained stable at 0.2vdc, hence the protection circuit was deceived | Edson Caeté |
| PHILIPS |
32PFL5604/78
|
Standby LED lights up red, does not turn on and does not accept commands | C474 4.7uf/16v next to the usb port, next to a cystal. | Replace without measuring | Eletrônica Barbato |
| PHILIPS |
32PFL5604/78
|
Standby LED lights up red, does not turn on and does not accept commands | C474 4.7uf/16v next to the usb port, next to a cystal. | Replace without measuring | Eletrônica Barbato |
| ELETROLUX |
MEF-28
|
Doesn't start | 4mhz crystal on display board | Defective crystal, replace it | MP ELETROINFO |
| SOUNDIGITAL |
SD1600. 1 HV 1 CANAL
|
Shaved parts 2 output c12 c12 = irs20957s / c13 = pwm si8244bb close to it c11 = smd sg3525a line diode has resistor 100r smd a lm393 low memory pic12f615 shaved 3 leds, roc = lm319m smd, regulator 5 pin sh1b =lmr 62014xmf mosfet irs20957s = 4 irfb4321 , near pwm si8244bb = mur1660ct 3 - transistor l3 I couldn't even reference 2 pre amplifier | Solution | Ok | Andre |
| EVO SOUND |
SD1600. 1 HV 1 CANAL
|
Shaved parts 2 output c12 c12 = irs20957s / c13 = pwm si8244bb close to it c11 = smd sg3525a line diode has resistor 100r smd a lm393 low memory pic12f615 shaved 3 leds, roc = lm319m smd, regulator 5 pin sh1b =lmr 62014xmf mosfet irs20957s = 4 irfb4321 , near pwm si8244bb = mur1660ct 3 - transistor l3 I couldn't even reference 2 pre amplifier | Solution | Ok | Andre |
| PHILCO |
TV PH32E32D LED
|
TV freezing, no sound, sound failing | Change ca815, ca804 and check u804, u805 and u807 | Eletrônica Barbato | |
| SEMP |
40L2600 / 32L2600
|
STBAY LED on but not turning on motherboard defect; client 8817 | Changing the q101 next to the power supply | Replace without measuring transistor with leak bc558 pnp | marcos melo cascavel ce |
| SAMSUNG |
51F4000
|
Turns on very weak and grainy image | Fet 9n25 on the y-sus almost at the tip of the board, tsound are two but only one was bad. I replaced it with the smk0460 and it was fine. | Sylvox | |
| LG |
42LB6200
|
TV doesn't turn on | Transistor q601 (k10a60w) shorted | Replace the mosfet | Robson RJM |
| FHILCO |
PH21M2
|
With the left side with a pre-strip | Replace capacitor 450 | Cícero Santos | |
| HQ |
HQS32NKH
|
No sound, or sound failing | Poor contact in the headphone connector. | Replace connector, or make a jumper between pins. | Pardal-x |